Search Documents

By J. D. Forrester, Erich Sarapuu, T. C. Cheasley

John G. Tripp-—The concept of converting fuel deposits in-situ to useful forms of energy and chemical raw materials has important possibilities as a means of stretching out our fuel resources. The authors have worked in this field for years and in fact are among the pioneers in developing in-situ techniques based on underground electrocarbonization. Their efforts have aroused great interest in this subject and their contributions will undoubtedly gain even more significance as time goes on. The 4 to 5 billion tons of petroleum are proved reserves, that is, they are completely defined and could be produced economically with present methods of recovery. Reserves of coal, tar sands, and oil shale shown in Table I are not equivalent to proved reserves as the term is used in the oil industry. Incidentally, the 4.3 billion tons of oil shown in the tabulation is equal to about 28 billion barrels of oil and, therefore, presumably does not include reserves of natural gas liquids estimated at about 5 billion barrels. The relative comparisons would be more complete if these liquids together with the reserves of natural gas were included in the tabulation. It is stated in the report that production costs of the order of 10c per million Btu's could be expected from a large industrial electrocarbonization installation. The authors state that the operation probably could be operated successfully and at a profit. I would like to express my view that for the operation to be profitable extremely favorable conditions would have to prevail. For example, the coal seam would have to be thick and close to the surface in order to minimize drilling costs; the deposit should be dry and so situated that there would be little, if any, inflow of ground water; and the seam would have to be relatively gas tight to avoid excessive gas leakage. Notwithstanding the tremendous strides that have already been made, it is my hope that the authors plan to continue their development work. Experiments on underground electrolinking and initial carbonization at Gorgas, Ala., indicate a need for improved control over the operation. Subsequent examination of the underground system at Gorgas has shown that the gasification zone did not always follow a direct path between the electrodes. Undoubtedly the control of the in-situ thermal processes can be improved by further development work. With respect to the electrocarbonization of oil shale it may be well to point out that the cost of mining oil shale is estimated to be 50c to 60c per ton. These are low mining costs as compared to coal. Thus it would appear that there is less economic incentive for applying in-situ thermal methods to oil shale than there is for applying these methods to coal. As is the case with in-situ methods for petroleum, the product from the shale having the most economic interest would be liquid oil rather than gas. The authors point out that for distances up to several hundred miles it is cheaper to transmit energy as electricity than it is to ship energy as coal. This is a very important point, and with coal shipping rates rising periodically, it could prove increasingly important in the future. I believe that the authors deserve great credit for their outstanding work on underground electrocarbonization. The knowledge resulting from their efforts is of great value to our fuels technology. James L. Elder—The experimental work conducted by the authors on the electrolinking-carbonization of carbonaceous materials in situ is of great interest. The method is of great importance in the development

Jan 1, 1955

By D. T. Van Zandt

IN the late 1920's rotary drills began to replace the churn drills in the petroleum industry, but until the middle 1940's the churn drill was the only widely accepted means of drilling large-diameter blastholes for quarry operations. The Calcite plant of the Michigan Limestone Div., U. S. Steel Corp., was one of the first to experiment with rotary drills for quarry blasthole drilling, and the first to employ compressed air on a fully rotary rig to cool the bit and raise the cuttings to the collar of the blasthole. The Calcite plant operates a limestone quarry near Rogers City, Mich., in the northern part of the lower Michigan peninsula. The formation quarried, a portion of the middle Devonian series, is the Dundee limestone, which is uniform, seldom massive, and characterized by definite bedding planes. The dip is southeast, 40 ft to the mile. Quarry faces vary from 20 to 116 ft in height. Vertical blastholes are used entirely, from three to five rows of holes being drilled parallel to the working face, spaced 18 ft apart with 18-ft burden and drilled 6 to 8 ft below shovel grade. Quarry operations coincide with the navigation season on the Great Lakes, as the bulk of the stone is transported by lake carrier. The normal operating season runs from April to December, the remaining time being devoted to stripping operations and plant and equipment maintenance. In the followirig discussion drilling rates mentioned refer to overall drilling time and include all operations such as moving from hole to hole, penetration and extraction of tools, and routine maintenance. Time consumed by such factors as power delays and major machine repair is not included in drilling time unless otherwise stated. Figures cover only operations at this one plant in the formation mentioned. Needless to say, a very different set of figures could be obtained in a different formation. However, the comparison of footage obtained with churn drills and rotary rigs in this particular formation has been used as an indication of what might be the expected performance of rotary rigs in other formations. Prior to 1950 the bulk of the blasthole drilling at the Calcite plant was done by electrically powered churn drills. Both crawler and wheel-mounted rigs were used. These machines, which mounted a 22-ft drill stem of 4½ in. diam and a spudding type of bit 2 to 4 ft long, drilled a hole of 5 ?-in. diam. Average drilling rate of these rigs in the Rogers City formation was 8 % ft per hr. In 1946 one of the first rotary blasthole drills offered to the quarry industry was put into use on an experimental basis. This machine, known as the Sullivan Model 56 blasthole drill, Fig. 1, was on 16-in. crawler pads and electrically powered at 440 v. The drill bit, a Hughes Tri-Cone roller bit of 5?-in. diam, Type OSC, was threaded into the end of the 4-in. square hollow drill rod or stem. These drill rods were 20 ft long with female threads on one end and male on the other to allow for addition of the desired number of rods for drilling holes of various depth. Rods were handled by a single drum hoist geared to the main drive motor and racked by a 30-ft derrick or mast when not in use. The cable from the hoist drum fed through a crown block on the top of the derrick back to the water swivel mounted in the top end of the drill stem in use. This cable remained attached during drilling operations and was used to hoist the tool string from the hole. Down pressure was applied to the tool string by means of a pair of 4-in. diam hydraulic cylinders acting on the drill chuck holding the drill rod. The first chuck consisted of flat jaws which gripped the flat sides of the stem. These jaws were controlled by set screws forcing them into contact with the drill stem. As these set screws had to be loosened and tightened by hand with each stroke of the hydraulic feed cylinders, there was great delay. For this reason the semi-automatic chuck was developed which automatically gripped the stem on the downward stroke but released for retraction of the hydraulic feed cylinders. Rotation was imparted to the tool string by a rotary table acting on the chuck and geared to the main drive motor through a separate gear train and clutch. A positive displacement water pump, mounted on the drill, fed water through a system of pipes and hose into the water swivel mounted on the top of the drill rod and through the rod and bit, washing the drill cuttings to the collar of the hole. Where water was scarce, provision was made to settle out the cuttings coming from the collar of the hole and re-use the water. Where water was abundant the stream coming from the hole was wasted. Drilling rate with this machine was about 20 ft per hr and bit life 1600 ft of hole. While this rate was more than twice that obtained with the churn drills employed, the problem of water supply and drill cuttings disposal rendered the machine impractical from an operating standpoint. Consequently it was used only in that part of the operation for which water was easily supplied, when the character of the formation made it least difficult to wash cuttings away from the collar of the hole. In October 1949 it was suggested that drill cuttings be removed by compressed air, long used for this purpose on pneumatic drills, and collected at the collar by suction. Thereafter, the water pump on the Sullivan 56 was replaced by a 500-cfm air compressor and a trial run made. Air pressure at

Jan 1, 1955

By M. T. Simnad, G. Derge, I. George

Measurements of current efficiency on iron-silicate slags in iron crucibles showed that conduction is about 10 pct ionic in slags with less than 10 pct silica and about 90 pct ionic in slags with more than 34 pct silica, increasing linearly in the intermediate range. The balance of the conduction is electronic in character. Silicate ions are discharged at the anode with the evolution of gaseous oxygen. Transport experiments show that the ionic current is carried almost entirely by ferrous ions, which may be assigned a transport number of one. THERE has been increased evidence in recent years that the constitution of liquid-oxide systems (slags) is ionic.1-3 The principal studies designed to establish the structure of liquid slags have been by electrochemical methods', " and conductivity measurements1,6,7 which also have indicated the presence of semiconduction in several silicate systems1,4-0 and in pure iron oxide.' It is well known that many slag-forming metallic oxides have an ionic lattice type in the solid state, and their properties are determined to a large extent by the lattice defects and ion sizes. As Richardson8 as pointed out, the detailed models of liquid slags cannot be found on thermodynamic data only but "must rest on a proper foundation of compatible structural and thermodynamic knowledge, combined by statistical mechanics." A careful thermodynamic study of the iron-silicate slags has been carried out by Schuhmann with Ensio9 and with Michal.10 They obtained experimental data relating equilibrium CO2: CO ratios to slag composition and made thermodynamic calculations of the activities of FeO and SiO, and of the partial molal heats of solution of FeO and SiO2 in the slags. It was found that the activity-composition relationships deviate considerably from those to be expected from an ideal binary solution of FeO and SiO2. However, the partial molal heat of solution of FeO into the slags was estimated to be zero. Their experimental results were correlated with the constitution diagram for FeO-SiO2 of Bowen and Schairer,11 with the results of Darken and Gurry" on the Fe-O system, and with the work of Darken"' on the Fe-Si-O system. All these studies were found to be consistent with one another. The variation of the mechanism of conduction with composition in the liquid iron-oxide-silica system in the range from pure iron oxide to silica saturation (42 pct SiO2) in iron crucibles was reported in a preliminary note." The current efficiency, or conformance to Faraday's law, showed some ionic conductance at all compositions, the proportion increasing with the concentration of silica. The current-efficiency experiments since have been extended. Furthermore, transport-number measurements have been completed in silica-saturated iron silicates to determine the nature of the conducting ions. Experimental Current Efficiency in Liquid Iron Oxide and Iron Silicates using Iron Anodes: This study was carried out by passing direct current through slags in the range from pure iron oxide to iron oxide saturated with silica (42 pct silica), using pure iron rods as anodes and the iron container as the cathode. A copper coulometer was included in the circuit to indicate the quantity of current passed during electrolysis. Assuming that the cation involved is Fe-+, the theoretical quantity of iron lost from the anode according to Faraday's law may be calculated and when compared with the actual loss observed, gives an indication of the extent to which Faraday's law has been obeyed. It also gives an indication of the presence and extent of ionic conduction in the melt. Preparation of the Slags: About 100 g of chemically pure Fe,O, powder is placed in an iron pot which is heated by induction until the contents liquefy. In this way, FeO is produced according to the reaction Fe2O3 + Fe = 3 FeO. More Fe2O3 or SiO, powder is added and, when a sufficient quantity of molten slag is obtained, the induction unit is turned off, the pot withdrawn, and the molten slag poured on to an iron plate. Homogenization and Electrolysis of the Slag: Apparatus—After considerable development, the setup illustrated in Fig. 1 proved to be quite satisfactory. A is an Armco iron cylinder, 1 in. ID and 1/8 in. wall, consisting of three sections placed one on top of the other. The bottom section is a pot about 5 in. long with a small hole drilled in its bottom to allow withdrawal of gases during evacuation of the apparatus. The middle section is 6 in. long and consists of a pot which serves as the slag container, while the top section is a hollow-cylinder continuation of the slag-container pot. The height of this latter section is about 5 in., giving an overall length of approximately 16 in. The iron cylinder is constructed in this way for ease of fabrication, the individual sections becoming welded together after the

Jan 1, 1955

By D. Turnbull, R. E. Cech

EXPERIMENTAL studies of precipitation of iron from solid solution in copper by Gordon and Cohen 1, Bitter and Kaufmann 2 and Smith 3 revealed that the precipitate particles were initially paramagnetic but could be changed to a ferromagnetic

Jan 1, 1955

By C. O. Bundranl, Peter Dehlinger, W. H. Browne

Brief laboratory investigations are described which attempt to determine optimum .sand concentrations in gel-sand and oil-sand1 well-treatments. The investigations apply to the case where sand acts as a propping agent in formation fractures. Both analytically and experimentally it is demonstrated that optimum sand concentrations can be defined. It is difficult to translate laboratory results to field treatments, however, since the relative distribution of sand and fluid in fractures may not be the same as injected. This is because fluid may penetrate the furtherest narrow portions of fractures, which would not pass sand. Optimum concentration of a monolayer of Ottawa sand in fractures of 0.025-in. width at the usual range of pressures encountered in treatments appears to be about 95 to 2 lb/gal. of gel. An investigation of abrasion of rock-walls by sand in treatments, described in the Appendix, shows that such abrasion is not probable in significant amounts. INTRODUCTION Experience in the Spraberry formation of West Texas, as well as in other formations, has shown that. sand is a necessary and vital part of gel-sand and oil-sand treatments. Many observers of treatments have also concluded that there seems to be an optimum range of sand concentration for these injections. Brief laboratory investigations were made at Battelle Memorial Institute to study flow in fractures with different sand concen- trations. To investigate the existence and range of optimum concentrations in the laboratory, however, necessitates knowledge of the mechanism by which the sand aids in increasing subsequent production. The action of sand in fractures is usually thought to be either that of a propping agent, thus providing a greater effective formation permeability; that of an abrasive in eroding fill material in fractures; or that of an abrasive eroding rock-wall irregularities along fracture surfaces. Investigations described in the Appendix show that sand does not appear to erode rock-wall materials appreciably. In a subsequent paper it is reasoned, at least for the Spraberry formation of West Texas, that the primary action of sand is not in removing fill materials in fractures. In this formation, and probably others, too, the main effect of sand appears to be that of a propping agent. Both analytical and experimental investigations were made for the case of a monolayer of sand acting as a propper, in which sand concentrations were determined that would, after treatment, permit flow of the maximum quantities of oil from the formation into a well. If too few sand grains are injected into fractures in which the bottom hole pressure has decreased appreciably below the original formation pressure, the confining pressure in the formation may become relatively large, thus compress the rock-walls around the sand grains, essentially close fractures, and so decrease the subsequent flow of oil. Similarly, if too much sand is used, the flow of oil will he impeded by the volume of sand present. THEORY Although an analytical approach to determining optimum sand concentrations involves gross assumptions.

Jan 1, 1955

Jan 1, 1955

By Benny Langston, Frank M. Stephens

Although little information is available concerning small-scale equipment for dust collection in laboratories, it is possible to adapt standard equipment for laboratory use. Dust from laboratory processes may be collected by cyclone separators, filters, electrostatic separators, scrubbers, and settling chambers. IN recent years much attention has been given to recovery, treatment, and disposal of dusts discharged into the atmosphere from operations of industry. considerable data has been accumulated on both operation and design of dust-collector equipment for commercial installations. On the other hand, there is almost no published data on design and construction of small-scale equipment to handle dust problems that arise in the ore-dressing laboratory. Dust-collection equipment such as multiclones, single-cyclones, scrubbers, chemical and mechanical filters, settling chambers, and electrostatic separators has proved its efficiency for collecting dust in industry. In the laboratory, however, the engineer is faced with the problem of collecting small quantities of dust, inexpensively, without diverting the major effort from the metallurgical problem to the problem of collecting dust produced by the process. For most applications standard dust-collection equipment is too large for use in the laboratory; however, for control of dust in large working areas it is often possible to use a standard dust collector, such as an air filter, with branch ducts to eliminate a health hazard. For example, the well-furnished sample-preparation room containing small jaw crushers, rolls, and pulverizers, in addition to the riffles and screens necessary for preparation of samples, presents a perennial source of dust. The authors' experience has shown that a combination system consisting of overhead branch ducts to the individual equipment and floor ducts with grills, where applicable, connected to a central dust collector effectively removes dust generated in preparation of samples. Fig. 1 is a sketch of a downdraft dust-collector for table installation. Similar systems can be built with floor grids. For portable equipment such as laboratory vibrating screens this type of installation with a steel grill to support the heavy load is reasonably efficient. Overhead branch ducts to individual crushing and grinding equipment, although efficient, must be carefully controlled by dampers to prevent excess loss or a change in the composition of the sample. Change in sample composition can result from excess velocity, which causes selective removal of constituents of low specific gravity. Fig. 2' shows the theoretical effect of terminal velocity on spherical particles of different specific gravities in air and water under action of gravity. Fig. 3 shows the effect of air velocity on composition of CaCO, coal mixtures. Although the entrainment of dust particles in a moving air stream is the basic mechanism by which all dust-collection equipment functions, usually intake velocity of the dust-collection system must be controlled to prevent loss of part of the sample. As an example of what may happen when excess velocities are used, a mixture of 50 pct coal and 50 pct limestone was crushed to —10 mesh and fed to a pulverizer equipped with an overhead dust-collection system. Fig. 4 shows the overhead dust-collection equipment used in this test. The pulverizer was set to give a product 95 pct —100 mesh in two stages. Velocity of air passing over the lip of the pulverizer was measured with an anemometer. After grinding, the finished product was analyzed to show the amount of calcium carbonate present. Fig. 3 shows graphically the increase in calcium carbonate as velocity through the dust-collection duct was increased. These data show that at a velocity of 1 ft per sec little if any of the coal was entrained by the overhead draft. At the maximum velocity, about 6.5 ft per sec, approximately 7 pct more coal was entrained than calcium carbonate. From an operating standpoint, this problem can be remedied easily by dampering the line to control velocity. The lowest velocity commensurate with satisfactory dust control should be used to prevent excess loss and, in some cases, selective dust loss. Collection of Dust in Laboratory Processes As in industry, the engineer desires to collect efficiently the dust produced by processes being investigated on a laboratory scale. However, in the collection of laboratory dusts he is faced with two additional problems: 1—The volumes of gas and the quantity of dust that must be recovered are small when compared with the capacity of standard dust-collector equipment, which must be scaled down in design except for collection of dust from large pilot-plant operations. 2—In addition, because of the variety of problems studied in the process laboratory, the engineer cannot design today a dust collector that will meet the conditions imposed by the processes of tomorrow. Sometimes, therefore, he must compromise collection efficiency to minimize the cost of fabrication and the amount of time diverted from the metallurgical to the dust-control problem. For collection of dust from laboratory processes a cyclone separator, filters, electrostatic separators, scrubbers, and settling chambers can usually be adapted for small-scale operations. The following

Jan 1, 1955

By B. Chalmers

THE practical importance of the phenomena of melting and freezing must have been recognized for a very long time. The difference between ice and water, for example, has had a profound influence on the history of mankind and the evolution of society. The possibility of melting a metal and allowing it to freeze in a mold of chosen shape has been an essential ingredient in our mastery of the art of shaping metals, and therefore in the evolution of the: machine age in which we find ourselves. The importance of melting and freezing, as applied to metals and alloys, has been so great, in fact, that empirical solutions have been found for the multitude of practical problems that have arisen. This approach has been so successful that relatively little attention has been directed to arriving at an understanding of the fundamentals of the processes. But metallurgy has come to a stage at which we may expect that some, at least, of the more complex problems that have not yet been solved (or perhaps even recognized) may be handled more effectively by scientific study, theoretical understanding, and logical experimentation than by trial and error. In this lecture, therefore, I propose to describe in outline what I think really happens when a metal freezes. In doing so I hope to explain many of the phenomena which have been observed, and in particular to account for the structures that are obtained in actual ingots and castings. The basic problem, to which this lecture represents a tentative partial answer, is this: a mass of metal, containing known proportions of various elements, is melted, heated to a given temperature, and then allowed to freeze under specified conditions. What will be the "structure" of the resulting metal? The term structure includes: 1—crystal size, shape, and orientations, 2—distribution of chemical elements, and 3-—shape, including cracks, cavities, pores, etc. The Solid-Liquid Interface We will first consider what takes place if a single crystal of a metal in the form of a rod is heated, not uniformly, but so that one end is hotter than the other. If this heating process is continued long enough, the hotter end will eventually melt; we will suppose that the rod is in a containing vessel so that the molten metal does not run away, Fig. 1. When some of the metal has melted, we have some solid, some liquid, and an interface or surface of contact between them. If the source of heat is now removed, the interface will move so that some of the liquid freezes, and if the supply of heat is suitably adjusted the interface will remain at rest. This very simple arrangement allows us to study the basic processes of melting and freezing, and if we fully understand this simple case, we may be able to account for what takes place under practical conditions where the heat does not all flow in the same direction, and where the heat flow is determined not by a controllable source of heat but by the heat capacity and temperature of metal and mold, and by the heat loss from the mold surface. The solid-liquid interface is evidently the region of the greatest interest to us; on one side of it there is crystalline solid, and on the other, liquid. In the solid, each atom has a well defined position, around which it vibrates as a result of thermal agitation. It only leaves this position in the relatively rare event of a "diffusion jump." The liquid is much less systematically organized. The atoms are about as far from their neighbors as in the solid, but the arrangement is much less systematic and is continuously changing. The solid and the liquid are represented diagrammatically in Fig. 2. The average energy of the atoms in the liquid is greater than in the solid by an amount that corresponds to the latent heat of fusion, i.e., the amount of heat that has to be supplied to convert unit mass of solid into liquid at the same temperature. The Two Processes As has recently been shown by Jackson and Chalmers,3 many of the features of the processes of freezing and melting can be understood if it is assumed that a continuous and rapid interchange of atoms between solid and liquid always takes place at a solid-liquid interface." It is necessary to con- sider two distinct processes, that of melting, in which atoms leave the surface of the solid and become part of the liquid, and the converse process,

Jan 1, 1955

By B. C. Woodfine

WHEREAS it is generally assumed that the highest temperature at which temper brittle-ness takes place is about 625°C, 1,2,3 Jaffe, Buffum, and coworkers have referred in several recent papers45,6,7 to the occurrence of temper brittleness in an SAE 3140 steel at 650" and 675°C. Their re- sults show that a considerable increase in transition

Jan 1, 1955

By M. R. J. Wyllie, P. F. Southwick

The importance of the so-called "dirty sand" or "conductive solids" problem in electric log interpretation was first stressed in a paper presented in 1949. Since that time the problem has been generally recognized as a most serious one. Several research papers bearing on the theory of the effects of clay contaminants on reservoir rock resistivities have appeared. These papers, while contributing to the theory of the problem, have not offered any practical solution. In the present paper an experimental investigation has been made of the effects of ion-exchange materials on the electrical properties of natural and synthetic porous media. The method used to make synthetic dirty sands is entirely novel and has proved a valuable guide to a better understanding of the properties of dirty sands generally. The effects of ion-exchange materials on both the resistivity and self potential (S.P.) logs have been examined. From the data obtained it has been possible to formulate a simple, practical method whereby electrical logs of dirty sands can be qualitatively interpreted. The method is in all essentials identical to that presently in use for interpreting clean sands. New light has also been thrown on the significance of the term formation factor when it is applied to dirty sands. In 1949 a paper was presented1 which showed that the presence of so-called "conductive solids" introduced considerable complexities into the analysis of the resistivities of dirty sands, i.e., permeable formations containing clay. The reduction of the self potential (S.P.) resulting from the presence of interlaminated shale or interstitial clay in permeable formations has been discussed by Doll.2,3 Noteworthy papers which dilate further upon the effects of shale and clay on the resistivity of permeable formations are those of deWitte,4,5 Berg,6 Wyllie,7 and most recently, Winsauer and McCardell.8 The last authors have endeavored to elucidate the chemistry of the resistivity phenomena in dirty sands in terms of an adsorption hypothesis. Specifically, they attribute the electrolytic conductivity of shales and clays within a permeable formation to an ionic double-layer effect and, for this reason, regard the term "conductive solids" as a misleading one. Some consideration has been given to the effect of dirty sands on the S.P. by Wyllie7 and by McCardell, Winsauer and Williams." Published work to date has cast light only on certain theoretical aspects of the problems created by the presence of clays and shales within permeable formations. One object of this paper is to describe experiments which serve to elucidate further the theory of the dirty sand problem and particularly the significance of the term "formation factor" as applied to dirty

Jan 1, 1955

Jan 1, 1955

By W. B. Mather

Of the 61 dikes examined some yielded cassiterite, tantalite, and beryl; eight contained spodumene; and six carried amblygonite. Two mines stockpiled spodumene as a byproduct. Only zoned pegmatite dikes carried lithium minerals. GEOLOGICAL studies have revealed the occurrence of hundreds of pegmatite dikes in northeast Brazil, Fig. I, in the three states of Rio Grande do Norte, Paraiba, and Ceara. Heretofore data have not been available on the possible production of lithium minerals from these areas, and in March, April, and May 1953 the author undertook a reconnaissance survey covering a cross-section of the pegmatite~. Sixty-one pegmatites were examined. The pegmatites of Rio Grande do Norte and Paraiba are located in an arid region (Seratao), and except in the most southerly portion there is a minimum of vegetation and overburden. The region is easily prospected and relatively accessible by jeep or truck. The pegmatites examined in Ceara are in an area of lush vegetation along the flanks of the Jaqueribe River valley. It is therefore more difficult to prospect, and the dirt roads, as a means of access, leave much to be desired. For all practical purposes rail transportation, except in Ceara, is not available. The rocks of the area are composed of Pre-Cambrian schist, gneiss, quartzite, and marbles. They have been intruded by granites, monzonites, and diorites and cut by quartz veins and pegmatites. Pre-Cretaceous erosion reduced the area to a peneplain upon which Cretaceous or younger sandstones were deposited. Recent erosion has left only a few remnants of these younger rocks. In most of the Rio Grande do Norte-Paraiba area the pegmatites were more resistant to erosion than the enclosing schists and therefore stand out in relief. This is not true in the rolling country of Ceara, where the pegmatites lack topographic expression. With regard to structure and lithology, the pegmatite~ of northeast Brazil are divided into two types, uniform and zoned. Of the 61 examined, 19 belong to the uniform and 42 to the zoned type. Uniform pegmatites are normally long, narrow, and tabular, with sharp contacts. They are composed of an intimate mixture of feldspar (microcline or ortho-clase), mica (biotite, phlogopite, or muscovite), and quartz. The grain size5 varies from fine at the contact to coarser in the interior. They are not considered a commercial source of pegmatite minerals, although efforts have been made to produce green beryl of gem variety. This type of dike is often abundant in schists and gneisses close to granite intrusives. The productive dikes — lenticular, pod-shaped, or irregular in outline, with sharp contacts — are of the zoned variety. Zone contacts are gradational, except for those with the quartz core. Zones re identified as follows, see also Fig. 3. Border Zone: This outer zone, in contact with the country rock, is composed chiefly of fine-grained muscovite and biotite, with lesser quantities of finegrained microline and quartz. It is the narrowest zone, usually measurable in inches. Wall Zone: Lying between the border and intermediate zones, the wall zone is composed of medium-grained feldspar (often microcline), muscovite, and quartz. Usually it is the widest zone. Widths of 50 ft were noted. Intermediate Zone: Lying between the wall zone and core, the intermediate zone is composed principally of coarse-grained microcline (occasionally with some orthoclase and albite). It may also carry minor amounts of coarse-grained quartz and fine to medium-grained mica. The width varies from less than 3 ft to more than 30 ft. Core: The center of the dike is composed almost entirely of massive quartz, occasionally with minor amounts of fine-grained muscovite. The width reaches 30 ft. Lithium and other minerals of potential economic value are found in the following zones:

Jan 1, 1955

By Elmer R. Kaiser

COMBUSTION of coal and transfer of heat from flames and gases to boiler surfaces continue to be of great interest to engineers here and abroad. Numerous investigations have been in progress to improve furnace and boiler performance and economy. The importance of better understanding of the processes and opportunities for improvement is apparent when it is remembered that heat from at least 500 million tons of coal a year the world over is being transferred to boiler water at efficiencies ranging mostly between 50 and 90 pct. Even slight gains in efficiency, economy, and labor saving become very significant when multiplied by the enormous quantity of fuel consumed. Also the competitive position of the large coal, oil, and gas industries in satisfying the fuel consumers is greatly affected by the achievements made through technical progress with each fuel. This paper is part of a continuing activity of Bituminous Coal Research, Inc., to extend the knowledge of coal utilization for steam generation and to seek promising directions for future research and development in cooperation with others. Particularly in the latter regard, numerous interviews were held during the last three years to seek the experience and advice of boiler and combustion-equipment manufacturers, electric-utility executives, and fuel engineers. A wealth of published information was also reviewed, which together with the interviews pointed to the advisability of further work on ash and sulphur control. For the present purpose a number of factors important to efficient heat liberation and recovery have been grouped as follows: 1—combustion, temperatures, and rates of heat liberation; 2—radiation, convection, and furnace and boiler configuration; 3—sponge ash, slag, and hard-bonded deposits; 4— low-temperature deposits and corrosion (cooling flue gas below dew point and air-pollution control); 5—the limitations of coal cleaning and boiler size and cost as related to fuel characteristics; 6—future possibilities and conclusions. The development of combustion apparatus for power boilers is progressing at a lively pace. There has been no letup in improvements in design of pulverized-coal-fired boilers, and there is a strong trend at present toward improving dry-bottom units. Spreader stokers with overfire jets and dust collectors as standard equipment are gaining favor. Less than 10 years in commercial use, cyclone burners are going into numerous installations here' and abroad.' Underfeed and traveling-grate stokers have long since been developed for heavy-duty operation, yet new developments in overfire jets and humidification of air blast have improved their performance. A water-cooled vibrating-grate stoker of German origin is being introduced into the United States and Canada." The primary objectives of an ideal coal combustion device are: capacity to burn the variety and sizes of coals likely to be economically available during the life of the unit; capacity to burn the coals automatically for a wide load range and rapid load fluctuations and to burn the coals completely to CO2, H2O, and SO2, which means without smoke and cinders, or carbon in the refuse; capacity to control and discharge all the ash in final granular form without ash adhesion to walls or tubes, and without flue dust; minimum furnace volume; minimum labor and maintenance; low initial and operating cost. Regardless of the method of burning, the gaseous products of coal combustion are N2, CO2, O2, H20, and SO?. By way of illustration, the coal analyses in Table I is assumed from an installation described by E. McCarthy.' When coal is burned with 20 pct excess air (theoretical air, 9.23 lb per lb of coal), the quantities of combustion gas shown in Table II are produced. In addition, the gases carry particles of fly ash, unconsumed cinders, soot particles, and small but significant amounts of vaporized oxides and sulphates of sodium, potassium, lithium, phosghorous, iron, and other metals. In recent years, germanium, one of the rare metals found in coal, has been shown to oxidize and vaporize at combustion temperatures and to be concentrated by reconden-sation at lower temperatures." Pulverized coal and cyclone flames" have peak temperatures of 3000' to 3500°F. Temperatures in fuel beds of large underfeed stokers reach maxima of 3000°F, sufficient to fuse almost any ash and to volatilize some of it. These peak temperatures are above the optimum necessary for rapid combustion, but they hasten heat transfer for ignition as well as boiler heat absorption. Furnace and gas temperatures increase with combustion air preheat. Low excess air has the same effect. Fine coal pulverization and highly turbulent combustion shorten the distance for fuel burnout, increase flame temperature, and speed up heat transfer. Rates of combustion of pulverized coal exceeding 200,000 Btu per cu ft per hr have been demonstrated in atmospheric gas-turbine combusters,

Jan 1, 1955

By Robert E. Brand, Strathmore R. B. Cooke

For a study of the bonding that occurs in magnetite pellets during oxidation, cubes of magnetite, hematite, and quartz were prepared, each with one surface polished and nearly optically plane. These faces were fired together under pressure and at various temperatures to determine whether bonding would occur. Sections of surfaces that bonded were examined microscopically. An attempt was made to measure the strength effected by this treatment. EARLIER work1,2 has shown that the strength developed by fired magnetite pellets containing silica or silicates is due to three separate effects. Two of these are associated with the formation of slag in the interior of each pellet at temperatures above 1000°C, where the atmosphere is substantially though temporarily neutral. The third is independent of the silica content and is responsible for the development of a hard shell around the pellet during the initial stages of firing, a condition which permits the pellet to assume the increasing load of the overlying burden and prevents extrusion of the slagged and semi-liquid interior. Pellets made from hematite concentrates do not show these effects unless specific additives are incorporated, and it is these differences in behavior which in large part account for the difficulty in producing satisfactory pellets from such concentrates. Elsewhere it has been stated that "the most important factor responsible for the development of strength in fired magnetite pellets containing no additive is the oxidation of magnetite to hematite and the subsequent recrystallization and grain growth of this constituent."' The object of the investigation reported in the present paper was to study in detail the mechanism described above and to evaluate its contribution to the strength of the fired pellet compared with other possible mechanisms, excluding slag bonding. This was effected by placing together polished faces of two cubes prepared from specific minerals and then heating them under constant pressure at different temperatures both in air and in nitrogen. The materials used were magnetite, hematite, and quartz. The magnetite was coarsely crystalline material from western Montana, the hematite was Itabira ore from Brazil, and the quartz was of optical grade but of unknown origin. A high-grade Lebanon (Pennsylvania) magnetite concentrate was used to prepare briquets for the investigation of bonding strength. Analyses of the iron oxide materials are given in Table I. The specimens for furnace treatment were prepared with a carborundum cut-off wheel, which cut the minerals into cubes approximating % in. along each edge. Care was taken to make the sides as parallel as possible. The edges of the faces to be polished were beveled, and the cubes were mounted in brass rings with sealing wax, this being essential to prevent the specimens from rocking during polishing. To prevent excessive friction, the wax was recessed so that only the brass ring and the face of each specimen would be in contact with the polishing lap. Each specimen was then ground with No. 600 carborundum to produce a level surface before polishing. The Graton-Vanderwilt process was not used for polishing because of the long time required by this method, but several other methods were tried. Cloth laps using levigated alumina or chromium oxide did not produce the desired polish. Satisfactory results were obtained by means of a pitch lap: which was used for all the mineral cubes, with levigated alumina as the polishing medium. The lap was operated in a machine similar to those used in the preparation of single optical surfaces. It was run at low speeds and moderate pressures, and polishing was stopped occasionally to prevent overheating of the lap. A good polish with flat surfaces could be obtained in about 5 min. After polishing the sealing wax was removed either in hot water or in a solvent such as turpentine.

Jan 1, 1955

By J. S. Levine

A series of four displacement experiments has been run in a large alundum core. Flow potential distribution in each liquid phase was measured continuously through oil-wet and water-wet capillary barriers, using a null-point pressure balance, and saturated distribution was determined from electrical resistivity measurements. A method has been devised for calculating the effective (and relative) permeability to each phase at any time and at any point in the flow system for the transient displacement process. Relative permeability points have been calculated and average curves drawn for oil displacing water and water displacing oil. The values of dynamic capillary pressure have also been determined. Data have been substituted into the generalized Buckley-Leverett fractional flow equation and a comparison between actual and theoretical breakthrough recoveries is shown. Displacement experiments have been performed in the laboratory for many years in an effort to determine the effect of a number of parameters on multiphase flow in porous materials. In the literature of petroleum technology, Wyckoff and Botset' were among the first to develop the relative permeability concept and to show experimentally that oil, gas, and water can flow simultaneously through a porous medium in a precise way governed by certain fluid properties, by the relative saturation of each fluid, and by characteristics of the medium itself. Somewhat later, Leverett2 and Hassler, Brunner, and Deahl11 developed some theoretical concepts of capillary behavior in porous materials. The work of Buckley and Leverett3 presented a theoretical analysis of immiscible liquid displacement based on the equation of continuity and the Darcy equation for viscous flow of each fluid. Subsequent investigators attempting to verify the Buckley-Leverett equation have, in general, deliberately neglected the capillary pressure term or have performed experiments in such a manner that it could be neglected. Terwilliger, et al4 in 1951, obtained agreement between theory and experiment for the constant rate displacement of water by gas in a long vertical sand column. Rapoport and Leas5 have investigated the

Jan 1, 1955

By B. D. Cullity, S. S. Hsu

The stress distribution at the surface of a twisted cylinder is analyzed along the boundary of a slip plane of arbitrary orientation and this analysis is applied to the torsion of cylindrical crystals of magnesium. A criterion for slip is developed and the critical resolved shear stress of magnesium in torsion is found to be 0.038 kg per sq mm. The mechanism of torsional deformation in magnesium and aluminum is described, as well as the relaxation of a twisted crystal at elevated temperatures. THERE has been considerable fundamental study A of the mechanism of slip occurring during deformation in tension and compression but comparatively little attention has been paid to the mechanism of torsional deformation. This paper is concerned with the way in which a single crystal deforms in static torsion and with the phenomenon of untwisting which a twisted crystal undergoes during annealing. Particular attention is paid to the application of the critical resolved shear stress law to torsional deformation. Probably the most likely mode of torsional deformation that can be imagined consists of rotation of one part of the crystal relative to another on the active slip plane. Here the most interesting feature is the slip direction. If a cylindrical single crystal is twisted about its axis and if, to consider the simplest case, the active slip plane is normal to the specimen axis, then the direction of gross slip at any point must always be at right angles to the radius drawn to that point. It follows that the crystallographic direction of slip must be continually changing, in sharp contrast to slip in tension which occurs in a crystallographically constant direction. Extensive investigations of slip in torsion have been made by Gough and his associates.' They made torsional fatigue tests on metal single crystals belonging to a number of different crystal systems and observed, with a microscope, the appearance of slip lines on the surface and of strain markings on the transverse cross section of cylindrical specimens. They concluded that the critical resolved shear stress law was just as valid in torsion as in tension, in the sense that slip occurred on that plane and in that direction in which the resolved shear stress was a maximum. They also established that the operative slip planes and directions were the same as in tension. They did not, however, measure the critical resolved shear stress in torsion nor, in fact, did they establish that a critical value of the resolved shear stress was necessary for the initiation of slip. Their investigations were, moreover, restricted to torsional fatigue tests which necessarily involve small strain amplitudes. Wilman,' studying crystal growth and the abraded surfaces of crystals, observed crystal fragments

Jan 1, 1955

Coal Division Mineral Industry Education Division Industrial Minerals Division Minerals Beneficiation Division Mineral Economics Division Mining, Geology and Geophysics Division Council R C Stephenson, Chairman (Ind Min Div), M D Cooper (Coal), H F Yancey (Coal), S D Michaelson (MBD), Will Mitchell, Jr (MBD), J R Van Pelt, Jr (MIED), S S Cole (Ind Min Div), J D Forrester (MGGD), L E Shaffer (MIED), E L Clark (MGGD), C W Merrill (MED), E H Robie, Acting Secretary, 29 West 39 Street, New York 18, New York

Jan 1, 1955

The pressure of the gas in equilibrium with sphalerite has been determined in the temperature range of 680' to 825°C, using the Knudsen orifice method. A comparison of these experimental pressures with those calculated from thermal data and from other equilibrium measurements shows that the vapor above sphalerite is predominantly dissociated ZnS. Equations have been given for correctly calculating dissociation pressures using the Knudsen orifice method. It has been shown that the experimentally determined pressure is the same, whether the zinc sulphide is sphalerite or not, or a mixture of wurtzite and sphalerite. CONFLICTING points of view appear in the literature on the constitution of the vapor in equilibrium with solid zinc sulphide in the vicinity of 800°C. By comparing the dissociation pressure calculated from thermodynamic data and the vapor-pressure determination of ZnS by Veselovski,1 Lumsden2 has concluded that the vapor consists largely of dissociated ZnS. Sen Gupta,' however, concludes from his spectroscopic determinations that the vapor is largely ZnS molecules. In view of the fact that the thermodynamically calculated' dissociation pressure is higher than that experimentally measured by Veselovski, it seemed in order to repeat Veselovski's measurements. Experimental Procedure The method used for the determination of the pressures in this papel- is the Knudsen effusion cell. The apparatus and procedure were described in a previous paper- from this laboratory on the determination of the vapor pressure of silver. The only difference is that the Knudsen cell in this work is made from platinum and there is no external cover around the cell. The cell is an ordinary platinum crucible of 2.2 cm top diameter with a capsule cover. It was thought that platinum might stand up at these temperatures to the solid and gaseous ZnS, since it was found that the weight of the platinum cell itself did not change appreciably on heating ZnS in it at the working temperatures. To insure that reaction of the zinc sulphide with the cell was not giving' a false value, a stabilized zirconia cell was employed for check runs. Fig. 1 shows the comparison, which is satisfactory. Veselovski previously had measured the vapor pressure of ZnS using a silica Knudsen effusion cell. On repeating his experiment in this laboratory, it was found that ZnS at-tacked the silica cell, giving it a marked frosty appearance. This led to the belief that Veselovski's result:; may be in error. Also, he was operating at pressures above the range ordinarily considered safe for the Knudsen method. The effusion rate was measured by weighing the cell before and after each run. The weight loss during heating to temperature and cooling down was measured and subtracted from the weight loss during the actual run. The zinc sulphide used in this investigation was from two sources: Fisher cp grade, and a sample of pure sphalerite supplied by Mr. E. A. Anderson of the New Jersey Zinc Co. Before and after the series of runs with Fisher ZnS, X-ray analysis showed that both wurtzite and sphalerite were present. However, the ratio of sphalerite to wurtzite increased. All measurements were made below the transition temperature which has been reported" to be 1020°C. The data obtained in this investigation are tabulated in Table I. The pressure was calculated by the usual Knudsen formula" on the assumption that ZnS molecules were effusing. From these data, using pure sphalerite in the platinum Knudsen cell, the vapor pressure of ZnS, in mm of Hg, as a function of temperature is given by the solid line in Fig. 1. The best straight line, as determined by the method of least squares, is given by 14405 logpzns =-14405/T +11.032. A comparison of these results with Veselovski's shows that his results are about 50 pct lower. Discussion The vapor in equilibrium with solid zinc sulphide in the temperature range of this study will consist of Zn, S2, and ZnS mol, since other species of zinc and sulphur' are relatively unstable. The question to be settled is whether or not ZnS is largely dissociated. The derivation8 which follows gives the method of calculating the pressure of zinc and sulphur over solid ZnS, assuming complete dissociation, from Knudsen cell data. The free energy of the reaction 2 ZnS(solid) ? 2 Zn(gas) + S2(gas) is given by ?F?° = -RT In K = —RT In p12p2 where p1 is the zinc pressure and p is the sulphur pressure. If dissociation occurs in a closed system,

Jan 1, 1955

By B. Fazan, O. D. Sherby, J. E. Dorn

McLean's technique was employed to determine the effect of temperature on the contribution of grain boundary shearing to the total creep strain in pure aluminum over the range of 610° to 747°K. The contribution of grain boundary shearing at the same stress was found to depend upon a temperature-compensated time, where the activation energy AH was practically identical with that for total high temperature creep. SEVERAL outstanding investigations by McLeanl-' have demonstrated that the total creep strain in polycrystalline aluminum at 473°K arises from microscopically detectable slip, subgrain tilting, and grain boundary shearing. Whereas microscopically detectable slip arises from dislocations that move out of the grains, subgrain tilting is due to entrapment of dislocations of like sign in subgrain bound-arles. Consequently, creep in polycrystalline aggregates appears to be the resultant of two mechanisms, namely, migration of dislocations and grain boundary shearing. This suggests that an appropriate law for creep should contain two additive terms ?1 = ?d + ?yb where the total creep strain, ?1, depends on the sums of the creep strains arising from motion of dislocations, ?d, and from grain boundary shearing, ?yb. But extensive investigations5 over wide ranges of alloys, grain sizes, temperatures, and stresses have shown that the total creep strain is quite accurately dependent on the single term functional relationship ?1 = f (?), s = constant where s is the stress (constant),* ? = te-?H/RT, t is the time under stress, AH is the activation energy, R is gas constant, and T is absolute temperature. Since Eq. 2 was found to be valid over those ranges where appreciable grain boundary shearing is observed, it appears probable that the activation energy for grain boundary shearing might be identical with the activation energy for migration of dislocations. Thus, under a given stress, it could be thought that where fd and fgb represent the appropriate functions for each mechanism of creep. The primary objective of this investigation was to obtain a direct check on the accuracy of this hypothesis. Experimental Procedure and Results Rolled aluminum sheet (99.987 pct Al), 0.100 in. thick, was used in this investigation. Creep specimens having a 0.25 in. wide, 3 in. long gage section were so machined that their axes were in the rolling direction. All specimens were annealed for 9 hr at 894°K before testing to produce a mean grain diameter of about 0.1 in. One face of each specimen was polished electrolytically in 10 pct HBF4. In order to permit accurate measurements of grain boundary shearing, the polished surface was lightly scribed with a ruling machine accurate to ±0.0001 in. to give a uniform grid of lines which were 0.01 in. apart. Although it was thought that surface working might modify the creep behavior in the vicinity of the scribed grid lines, this technique nonetheless was employed because such local differences in creep properties should not modify seriously the fractions of the total creep strain due to grain boundary shearing or to migration of dislocations. All creep tests were conducted under constant load with an initial stress of 250 psi. The specimen tem-

Jan 1, 1955

By M. B. Bever, A. B. Michael

The solidification of aluminum-rich aluminum-copper alloys was investigated for different solidification rates. The measured amounts of nonequilibrium eutectic were compared with the amounts calculated on the assumption of no diffusion in the solid. The morphology of the eutectic was studied and dendritic spacings were measured. Compositions of the cored primary solid solutions were determined by quantitative autoradiography after activation of the solute copper by neutron irradiation. CONSIDERABLE progress has been made in recent years toward an understanding of the solidification of metals. This is especially true for the factors involved in nucleation, the controlled growth of metal crystals from melts, and various aspects of the freezing of ingots and castings. Many features of the solidification process, however, are not understood adequately and much further work is required. In the research reported here the solidification of a series of aluminum-rich aluminum-copper alloys was investigated. Different degrees of deviation from the idealized case of equilibrium solidification were attained by varying the rate of solidification. Thermal analysis and microscopic examination were supplemented by lineal analysis and autoradiography. The latter required the use of radioactive tracers and was adapted to the quantitative determination on a microscale of concentrations of copper dissolved in aluminum. The tracers were produced in situ by activating the copper with neutrons. These techniques permitted a correlated interpretation of the temperature-time history, the amounts of nonequilibrium eutectic and the general morphology of the alloys, and yielded quantitative data on microsegregation. Nonequilibrium Solidification In the general case of the solidification of a solid solution in accordance with the phase diagram, the composition of the coexisting liquid and solid must change continuously. This change requires diffusion, which at best remains incomplete in the solid during solidification. The resulting inhomogeneity of the solid solution crystals is well-known as coring, dendritic segregation, or microsegregation. The generally accepted analysis of coring assumes that, 1—no diffusion occurs in the solid, 2—diffusion is complete in the liquid, and 3—the composition of the solid formed on cooling through any infinitesimal temperature interval is given by the solidus of the phase diagram. On this basis, In this equation m designates mass, x designates the concentration of solute and the subscripts L and S refer to the liquid and solid phases, respectively; the subscript o indicates the initial state, in which the liquid is identical with the entire system. Eq. 1 or its equivalent has been derived repeatedly'-7 and an analogous equation, known as Rayleigh's equation, has been used for distillation. The assumptions on which Eq. 1 is based do not include an infinitely fast cooling rate as sometimes stated. In fact, Olsen and Hultgren %ave shown by experiment that very high solidification rates suppress coring, presumably by preventing diffusion in the liquid and by the effect undercooling has on the composition of the nucleus. Coring thus occurs at rates of cooling which are too fast for a close approach to equilibrium in the solid and too slow to suppress diffusion in the liquid and to cause marked undercooling. If the liquidus and solidus approximate straight lines, Eq. 1 simplifies to The fraction of liquid present at any temperature during nonequilibrium solidification can be calculated from Eqs. 1 or 2. By the lever relation it is

Jan 1, 1955