Search Documents

By B. E. Eakin, R. T. Ellington

An apparatus and a procedure for determining the viscosity behavior of hydrocarbons at pressures up to 10,000 psia and temperatures between 77 and 400° F are described. The equipment is suitable for measuring viscosity of either the liquid or vapor phases or the fluid above the two-phase envelope for systems exhihiting retrograde phenomena, according no the phase state of the system within these ranges of temperature and pressure. Equations are developed for calculation of viscosity from the experimental measurements, and new data for the viscosities of ethane and propane at 77° F are reported. INTRODUCTION With the advent of higher pressures and temperatures in industrial processes and deep petroleum and natural gas reservoirs, demand has increased for accurate values of physical properties of hydrocarbons under these conditions. Proportionately, more frequent occurrence of natural gas and condensate-type fluids is encountered as fluid hydrocarbons are discovered at greater depths. This increases the importance, to the reservoir engineer, of being able to predict accurately the physical properties of light hydrocarbon systems in the dense-gas and light-liquid phase states. Reliable gas viscosity data are limited primarily to measurements made on pure components near ambient temperature and at low pressures. Few investigations have been reported for high pressures, and except for methane, data on light hydrocarbons are subject to question. This is demonstrated by the large discrepancy between sets of data on the same component reported by different investigators. For mixtures in the dense gas and light liquid regions and for fluids exhibiting retrograde behavior there are very few published experimental data. Viscosity data for methane have been reported by Bicher and Katz,1 Sage and Lacey,12 Comings, et al,3 Golubev,3 and Carr,3 with good agreement among the last three sets of data. Comings, Golubev and Carr utilized capillary tube instruments for which the theory of fluid flow is well established. The theory permits calculation of the viscosity directly from the experi- mental data and dimensions of the instrument alone. Sage and Lacey, and Bicher and Katz used rolling-ball viscometers. The theory of the rolling-ball viscometer has not been completely established, and these instruments presently require calibration by use of fluids of known viscosity behavior before viscosities of test fluids can be measured. To obtain accurate data it is necessary that the rolling-ball viscometers be calibrated by use of fluids of density and viscosity similar to the test fluids, a difficult selection for the gas phase. From the methane data and experimental tests on various natural gases, Carr developed a correlation for predicting the PVT behavior of light natural gases.2,3,4 This correlation was based on data for a very limited composition range; its application to rich gases and condensate fluids is questionable. The object of this investigation is to develop an instrument which can be used to obtain viscosity data at reservoir temperatures and pressures, for rich gases, condensate-type systems above the two-phase envelope and light liquid mixtures. These data will be used in an effort to develop correlations to represent the viscosity behavior of these fluids. APPARATUS In a previous viscosity study Carr2 utilized a modified Rankine capillary viscometer configuration," Fig. 1. In this instrument the gas to be tested is forced through the capillary tube in laminar flow by motion of a mercury pellet in the fall tube, the measured displacement time being that required for the mercury slug to move between the brass timer rings. The viscometer is constructed of glass and mounted in a steel pressure vessel. The test gas pressure in the viscometer is balanced by an inert gas (usually nitrogen) in the vessel. Excellent results have been obtained with instruments of this type, with Carr2 and Comings5 reporting repro-ducibilities of 99.5 to 99.3 per cent and an estimated absolute accuracy of 99 per cent. However, these instruments have limitations which have precluded their use for liquids. The need for maintaining a balance between pressures of the test fluid and inert gas in the viscometer vessel presents operating problems, and requires charging the test fluid to the viscometer very slowly. The principle drawback to the Rankine unit is behavior of the mercury slug which provides the pressure differential across the capillary. When even trace quantities of propane or heavier hydrocarbons are present in the test gas, the mercury tends to subdivide

By C. D. Hall, F. E. Dollarhide

Fluid Ioss agent.s for crude oil and for water have been studied in dynamic tests. A treatment using a spearhead with a fluid loss agent followed by plain fluid appears feas ible in crude oil, but not in water. An equation for spearhead depletion shows that spurt loss relative to fracture width must be low, if the portion of spearhead fluid in the treatment is to be small. The presence of colloidal matter in crude oils aids the fluid Ioss agent. Unlike in kerosene, where flow limited the agent deposition, in crude oils the filter cake continually formed and leak-off declined. The volume-time relation varied somewhat for different crudes, but was best described by a square root of time function. Spurt loss was inversely proportional to agent concentration. After the fluid loss agent initiated the filter cake, the crude oil colloids built on it effectively. A 2-minute or a 5-minute spearhead with double the normal agent concentration gave the same fluid Ioss curve as the same concentration did for a 30-minute test. The agents tested in water gave fluid Ioss plots on which, for the first few minutes, volume was proportional to the square root of time, but later became proportional to time. For fracture area calculation the customary square root of time function is a satisfactory approximation. Leak-off rates and spurt losses were higher in water systems than in oils. The spurt Ioss tended to be inversely proportional to concentration. In spearhead tests, the filter cakes were not eroded by water flow. However, the rather high spurt loss values make spearhead treatments impractical for water-based fluids. Introduction The effects of dynamic testing conditions on the performance of fluid loss agents in kerosene have been studied previously.' We have extended the work to include crude-oil- and water-based fracturing fluids. An understanding has been gained of the mechanisms of formation and functioning of the filter cakes of fluid loss agents. The practical aspects of evaluating performance of agents in relation to fracture area calculations also are considered. The feasibility of using the fluid loss agent in a spearhead stage of the treatment is examined further for both types of fluids. Experimental Procedure The dynamic fluid loss tests were performed in an apparatus similar to the high-pressure apparatus described in a previous publication.' A fracturing fluid was circulated over a rock surface located in a closed pressurized loop. The fluid flowed axially over the cylindrical surface of a core 2 in. in diameter X 3.5 in. long, mounted (with the flat ends sealed off) in a pipe, with 0.117 in. annular clearance. The filtrate was collected in a central hole in the core and led through valves to graduated cylinders. Provision was made for changing quickly the circulating fluid during the test (spearhead runs) without interrupting the filtration pressure. The only modifications were to add heating tapes and water jackets for the tests with crude oils, all conducted at ISOF, and to change all parts exposed to the test fluid to stainless steel for the tests with water-based fluids. The latter tests were made at room temperature, 80F. Three crude oils were tested. A mixed crude, obtained from a local refinery, contained a considerable amount of light ends. For safety reasons, it was stripped to 250F vapor temperature before use in the fluid loss tests. The other two oils were used as obtained from lease tanks. One was a greenish-brown, 37" API paraffinic crude, and the other was a black, 32" API asphaltic crude. The fluid loss agent for oil, here designated for brevity as Agent A, was Adomite@ Mark II*, a granular solid commercial agent, the same as previously tested in kerosene.' Three different compositions of fluid loss agents were tested in Tulsa tap water. Agent B was adomit& Aqua*, a solid commercial fluid loss agent, comprising clays and hydrophilic gums principally derived from starch. Agent C was a mixture of three parts of Agent B with two parts of silica flour. Agent D was Dowel1 J137, a mixture of guar gum and silica flour. The test cores were cut from contiguous blocks of Berea or Bandera sandstones. For the oil tests, the cores were oven dried, evacuated, saturated with kerosene, and the kerosene permeability was measured. The cores used with the water-based fluids were pretreated by saturating with 3 percent calcium &loride solution to minimize pemeability damage by the fresh water due to clay migration. The

Jan 1, 1969

By N. A. D. Parlee

The diffusion rate of hydrogen in liquid iron has been measured by a gas-liquid metal diffusion cell technique. The diffusion cell was formed by immersing an alumina tube containing hydrogen gas at 1 atm in a bath of stagnant liquid iron. The change in the composition of the melt in the cell was determined by measuring the rate of absorption of the gas in the cell. The appropriate solution to Fick's second law was used to examine the data and calculate diffusivi-ties. The absorption of hydrogen in stagnant pure liquid iron has been found to be diffusion-controlled. The results show that the chemical diffusion coefficient, D, of hydrogen in pure iron in the range of 1547" to 1726°C can be represented by the following Arrhenius relation: D(sq cnz per sec) = 3.2 x X exp(- 3300 i 1800/RT) where the uncertainty in the activation energy corresponds to the YO pct confidence level. Oxygen in the melt (above 0.015 pct 2) increased the apparent rate of absorption of hydrogen. The importance of diffusion data on liquid metals for predicting the rates of certain metallurgical processes has been recognized for a long time. Moreover, these data are much needed to test and develop theory for diffusion in liquid metals. Despite this practical and theoretical interest, however, relatively little reliable information about diffusion in liquid metals is available in the literature. This is particularly true for gas components such as hydrogen, oxygen, and nitrogen in liquid metals, where almost no data on chemical diffusion coefficients are to be found. This is probably due to a multitude of experimental difficulties particularly associated with high-temperature melts. In an effort to fill this gap in information, a research program was undertaken to study the diffusivities and rates of solution of gases in liquid metals. This paper presents the results of a study of the diffusion of hydrogen in liquid iron. EXPERIMENTAL METHOD Two methods for the study of the kinetics of dissolution of gases in liquid metals are being employed in this laboratory. Both involve the measurement of the volume of gas absorbed by the melt as a function of time and as such both avoid the uncertainties involved in chemical analyses of quenched samples for relatively small amounts of gas. In the first method, the gas dissolves in an inductively stirred melt and, in the absence of a slow surface reaction, the results are often interpreted in terms of mass transport across a liquid "boundary layer" between the homogeneous gas phase and well-stirred part of the melt. Other interpretations of the results of such experiments have also been described in the literature.1'5 In the second method a gas-liquid metal diffusion cell is used.' The gas dissolves in a cylindrical column of stagnant liquid metal and, in the absence of a slow surface reaction, the results are interpreted in terms of a non-steady-state diffusion solution to Fick's second law. The weakness of the first method is that while it gives information on the mechanism of absorption by stirred melts it yields an overall rate constant which even in the simplest cases depends on the nature and the thickness of the "mass transport layer" or "boundary layer". It yields no values of diffusion coefficients. The second method was used in this research because in many cases it is possible to determine the diffusion coefficient of the gas component in the liquid metal. In this research it has been utilized to measure diffusion coefficients of hydrogen in liquid iron. The apparatus used was essentially the same as that described by Mizikar, Grace, and par lee but certain modifications have been introduced to meet the elevated temperatures and special conditions of this research. Fig. 1 is a schematic drawing of the apparatus and Table I gives the identification of various parts in this figure. The diffusion cell, shown in detail in Fig. 2, was formed by immersing an impervious alumina tube (hereafter called absorption tube) in a bath of pure liquid iron contained in an alumina crucible. Two types of tubes were used, Morganite triangle RR and McDanel AP35. The crucible was contained in a vertical impervious alumina combustion tube (32 mm ID by 914 mm long) which was closed at both ends by water-cooled brass heads employing O-ring compression seals, Fig. 1. A protection tube enclosing a Pt, 5 pct Rh-Pt, 20 pct Rh thermocouple was introduced through the lower end of the combustion tube

Jan 1, 1968

By T. F. Kassner

The dissolution kinetics of type 304 stainless steel in the Bi-Sn eutectic alloy have been investigated under the well-defined hydrodynamic conditions produced by the rotating-disc sample geometry. In addition, the mutual solubilities of iron, chromium, nickel, and manganese from 304 stainless steel in the eutectic alloy were determined over the temperature range 450" to 985°C. The convective -diffusion model for mass transport from a rotating disc was used to interpret the experinlental dissolution data. The dissolution process was found to be liquid-diffusion-controlled under specific conditions of temperature and Reynolds number. Liquid penetration into the 304 stainless steel resulted in a reduction of the di,ffusion-controlled mass flux and thus precluded the calculation of the diffusion coeficients of the four components from 304 stainless steel in the Bi-Sn eutectic alloy. The convective-diffusion model for diffusional limitations of electrode reactions and mass transport at the tationssurface of a rotating disc set forth by Levich 1,2 has found wide applicability in the investigation of electrochemical and dissolution phenomena in aqueous systems. Riddiford 3 and Rosner have reviewed the model and also include numerous references on work of this nature. More recently the rotating-disc system has been applied to the investigation of hetereogeneous reactions in liquid-metal systems. Shurygin and Kryuk 5 have measured the dissolution rates of carbon discs in molten Fe-C, Fe-Si, Fe-P, and Fe-Ni alloys. Shurygin and shantarin6 also studied the dissolution kinetics of iron, molybdenum, chromium, and tungsten, and the carbides of chromium and tungsten in Fe-C solutions with a rotating-disc sample geometry. In these systems it was possible to distinguish between diffusion and reaction control mainly through experimental confirmation of the velocity dependence of the dissolution rate predicted by the model. However in the absence of dependable solubility data and the virtual lack of diffusion data in these systems, a quantitative check of the magnitude and the temperature dependence of the rate was not possible. In many instances, estimates of the activation energy for solute diffusion and the diffusion coefficient based upon the experimental dissolution data are not credible. A recent study by this author7 has resulted in a critical test of the model in a liquid-metal system. The solution rates of tantalum discs in liquid tin were measured over a wide range of temperature and velocity conditions. In addition, the solubility and diffusion coefficient of tantalum in liquid tin were determined as a function of temperature. The latter data were used with the model to predict both the magnitude and the temperature dependence of the dissolution flux. In that work it was also deemed necessary to reevaluate the solution to the convective diffusion equation to incorporate the effect of the lower range of Schmidt numbers encountered in liquid-metal systems. Good agreement between the model and the experimental dissolution data in the region of diffusion control was obtained in the Ta-Sn system. The Bi-Sn eutectic alloy is used as a seal between the reactor head and the reactor vessel in the Experimental Breeder Reactor-11. The alloy is fused periodically prior to fuel-handling operations. In that connection, it was necessary to investigate the compatibility of the liquid alloy with the type 304 stainless-steel containment material. The results of a rotating-disc study in this multicomponent system are presented. EXPERIMENTAL METHOD The 5.08-cm-diam discs were machined from 0.317-cm-thick plate. Chemical analysis information for the type 304 SS material is given in Table I. The discs were ground flat on metallographic paper and given a final polish on Linde B abrasive. A thin support rod was threaded into the disc and the region around the threads was fused under an inert gas. The support rod was fitted with a quartz protection tube and then was attached to a supporting shaft which passed through a rotary push-pull vacuum seal. The disc and supporting shafts were dynamically balanced prior to insertion into the furnace tube. The apparatus is shown schematically in Fig. 1. The 58 pct Bi-42 pct Sn eutectic alloy melts were prepared from 99.995 pct pure Bi and Sn by fusing the components in a 7-cm-ID Pyrex crucible. The system in which the melts were made was evacuated to a pressure of 1 x 10-6 Torr and back-filled with purified argon several times before melting the charge. The ingot was reweighed and placed in a slightly larger-diameter Vycor crucible used in the dissolution runs. A run was started by lowering the disc into the liquid

Jan 1, 1968

By J. B. Clark, A. J. McEvily, R. L. Snyder

The nonuniform distribution of precipitate particles has been recognized as a leading factor contributing to the relatively low fatigue resistance of aluminum alloys. The structure of many of these alloys is characterized by narrow precipitate-free zones adjacent to the grain boundaries. Alloys with such zones exhibit a tendency for brittle inter crystalline fracture. The interrelation between this type of structure and mechanical properties was investigated in an Al-10 wt pct Mg alloy. It was found that deformation during fatigue occurs preferentially along these zones and cracks initiate there. In Al-10wt pct Mg, the zones were found to be supersaturated even after extensive general precipitation and are due to the absence of proper precipitate nuclei in the region near the grain boundaries. Cold working the alloy prior to aging improves the mechanical properties by inducing precipitation within the zones and also by jogging of grain boundaries. The mode of fracture is changed from brittle inter crystalline to more ductile trans granular fracture. THE process of fatigue is highly structure sensitive, with the strength of the whole often dependent upon some localized discontinuity, either geometrical or metallurgical in nature. Much has been learned about the role of geometrical discontinuities, e.g., notches, in fatigue, but with the exception of the effects of inclusions or the shapes of carbides, relatively little is known about the specific effects of discontinuities in metallurgical structure such as nonuniform precipitation. In most age-hardening aluminum alloys, metallo-graphic studies have shown that the extent of precipitation adjacent to grain boundaries is much less than that which occurs in the interior of the grains. The width of these almost precipitate-free regions, which are sometimes called denuded zones, and the extent of solute depletion within them, are dependent upon the particular alloy and its aging treatment. It has been observed1 that these zones are relatively soft with the result that plastic deformation takes place preferentially within them. It has also been shown 2-4 that there exists a tendency for intercrys- talline cracking in fatigue when such zones are present. It is of interest to note that Broom et al.2,3 were able to reduce the incidence of this type of failure in an A1-4 wt pct Cu alloy by stretching the material 10 pct prior to aging. In the present study, the effects of precipitate-free regions on the fatigue properties of an A1-10 wt pct Mg alloy were studied in detail, and the effects of deformation prior to aging on the nature of the precipitation process as well as on fatigue properties were also investigated. MATERIAL AND PROCESSING An A1-10 wt pct Mg alloy was selected for this study, because it was known that well-defined precipitate-free regions along the grain boundaries are readily obtained in this alloy after aging at 200oC.5 The starting materials were 99.998 pct A1 and singly sublimed magnesium of about 99.9 pct purity. The aluminum was induction melted in a graphite crucible, and then the magnesium addition was immersed until dissolved. Chlorine gas was then bubbled through the molten alloy for 4 min to degas the melt, after which the melt was cast at a pouring temperature of 730" to 760°C into a cold, graphite-coated, tapered steel mold. Since A1-Mg alloys are difficult to homogenize,5 special care was taken to obtain a uniform composition. Two-in. cubes were cut from the ingot and heated at 446°C for 30 min. These cubes were then hot forged approximately 35 pct in each of the three cube directions and homogenized for 16 hr at 446°C. Sheet specimens were then obtained by pressing 40 pct and rolling 35 pct per pass with reheating between reduction steps to a final thickness of approximately 0.10 in. The sheet was then solution treated for 16 hr at 446°C and water quenched. The age hardening behavior of this material at 200°C was then determined, and the results are shown in Fig. 1. The age hardening of this alloy when subjected to cold work prior to aging is also shown in this figure. Preliminary work indicated that extensive deformation after quenching was required to affect drastically the precipitate-free regions in this alloy, and a rolling reduction of 50 pct was chosen. For purposes of comparison the following three conditions were studied: a) Solution treated, quenched, and aged 20 hr at 200°C

Jan 1, 1963

By H. R. Ogden, E. S. Bartlett, A. G. Imgram

Unmodified disilicide coatirigs were applied to sheet-tensile specimens ofCb-Dg3 and Mo-TZM veJractovy- metal alloys. Coating thickness, degree of coating-substrate interdiffusion, and specimen geonzetry (notched and plain were included in the variables studied. Tensile tests were made to determine the ductile-lo-brittle transition temperature. The disilicide coating modestly increased the transition temperatlre of TZM, but had no effect on 043. Neither material condition (recrystallized or stress-velieved) nor specimen geometry (notched or unnotched) significantly altered the effects of coatings on the transilion temperatures of. the alloys. Cracks in the brittle coatings did not propagate into the substrate, and fracture modes appeared to be the same for both un-coated and coated specimens. MOST potential structural applications for refractory metals and alloys involve exposures to oxidizing environments at elevated temperatures. The general lack of oxidation resistance of these metals will require protective coatings to allow fulfillment of their potential. Currently preferred coatings for the oxidation protection of refractory metals are brittle intermetallic aluminides or silicides. These are typically formed on the surface of the refractory-metal substrate by a diffusion reaction between the substrate and a gaseous or liquid medium that is rich in aluminum or silicon. Because of the brittleness of these coatings, they will sustain no plastic deformation at low temperatures. They are frequently cracked by cooling from the coating temperature because of the thermal-expansion mismatch with the substrate alloy. Even if they survive cooling intact, they crack rather than sustain deformation under load at low temperatures. Thus, when a coated refractory metal is strained beyond the elastic limit of the coating at low temperatures, the mechanical environment of the substrate would include both static and dynamic cracks. These might be expected to influence the flow and fracture behavior of the substrate. This could be manifested in an altered fracture mode and/or an increase in the normal ductile-to-brittle transition temperature of the refractory-metal substrate. This paper presents the results of a research program that was conducted to determine the influence of the presence of a brittle surface coating on the low-strain-rate tensile behavior of typical refractory metals at low temperatures. EXPERIMENTAL PROCEDURES Material Preparation. Thirty-mil-thick sheets of molybdenum TZM alloy (Mo-0.5Ti-O.1Zr) and colum-bium D43 alloy (Cb-IOW-1Zr-O.1C) were obtained commercially. These alloys were selected as substrate materials representing two classes of materials important in current refractory-metal technology. The TZM was in the stress-relieved condition, and exhibited a heavily fibered grain structure. The D43 had been processed by the duPont "optimum" fabrication schedule,' and exhibited slightly elongated grains typical of this process. Tensile specimens of two geometries were prepared from these materials: 1) plain specimens with 0.2-in.-wide 1.0-in.-long gage sections; 2) specimens similar to above, but with a 0.06-in.-diam hole drilled in the center of the gage section, providing a stress concentration factor, Kt, of 2.5. The "notch" geometry was selected to represent a typical condition of a rivet hole or other geometric discontinuities as might be encountered in various applications. Machined specimens were degreased, with a final rinse in acetone, prior to the application of coatings. Specimens of each substrate and configuration were pack-siliconizedin a particulate mixture of 80 pct A1203, 17 pct Si, and 3 pct NaF. Specimens were embedded in this mix (contained in graphite retorts) and coated in an electrically heated argon-atmosphere furnace under time-temperature conditions to effect nominal 1- and 3-mil-thick silicide coatings: Coating Thickness, mils Thermal Treatment 0.6 to 1.4 24 hr at 982°C 2.4 to 3.2 48 hr at 1093°C Coating kinetics were similar for both the TZM and D43 substrates. These treatments had little or no visible effect on the substrate microstructure as determined by optical metallography. The coatings on TZM were essentially single-phase unmodified disilicides, while those on D43 showed substantial evidence of modification by proportionate reaction with the respective substrate elements or phases, as shown in Fig. 1. It was recognized that these coatings might not be particularly desirable regarding protective capability. However, it was desired to circumvent possible inter -ferring chemical interaction with the substrate by pack additives such as chromium, titanium, boron, aluminum, and other elements that typify the better protective coatings for these materials.' Thus, the results presented apply specifically to the simple silicide coatings investigated. They may not be rep-

Jan 1, 1967

By A. Gatti, R. L. Fullman

A very fine dispersion of aluminum oxide is produced by internal oxidation of solid-solution alloy of 0.14 pet A1 in Ag. The particle size of the aluminum oxide is approximntely 50 to 100A in radius. The yield strength of the alloy is increased markedly by internal oxidation. A further increase in strength is produced by cold working the internally oxidized alloy. Recrystallization is retarded by the finely dispessed aluminum oxide particles, so that the strength increase resulting from cold work is retained on annealing at temperatures 14 to about 700°C. MANY workers'-3 in the past have studied various aspects of the internal oxidation of aluminum-silver alloys. This paper is an extension of these studies with emphasis placed on the effect of time and temperature of annealing on the strength of these alloys after oxidation and subsequent cold working. Two general conditions are necessary to internally oxidize an alloy. First, oxygen must diffuse through the base material more rapidly than does the addition; otherwise oxidation will take place as a surface layer. Secondly, the affinity of oxygen for the addition must be greater than for the base material. After internal oxidation of certain alloys takes place, a marked increase in hardness accompanied by higher yield stress and improved creep properties is noted, presumably as a result of the highly dispersed oxide within the base material. Meijering and Druyvesteyn1 also noted that the internally oxidized portion of a partly oxidized alloy failed to recrys-tallize under annealing conditions that led to coinplete recrystallization of the unoxidized part. EXPERIMENTAL-METHODS AND PROCEDURES Few alloys can be made to contain a second phase that is extremely stable at high temperatures. Silver plus aluminum in solid solution was chosen for these internal oxidation studies because of the high rate of oxygen diffusion through silver and the very stable nature of aluminum oxide. Two alloys were vacuum cast. The nominal compositions were: Alloy A—1 pct Al, balance Ag; Alloy B—0.1 pct Al, balance Ag. Chemical analysis, which does not distinguish between aluminum and aluminum oxide, showed the conlposition to be: Alloy A—1.6 pct Al, and Alloy B—0.14 pct Al. The ingots were machined for surface cleaning, swaged and drawn to 0.020-in. diam wire. A sample 20 ft long of the 0.020-in. dianl wire of each composition was annealed 24 hr at 800°C in pure dry hydrogen. Each wire was then cut into two equal pieces. Photomicrographs of the 0.14 pct A1 alloy are shown in Fig. 1, the annealed 0.020-in. wire at the left and the oxidized wire to the right. The oxidation treatment for the first set of data was 1000 hr at 800°C in air. After this treatment the 1 pct A1 proved to be brittle. It is assumed that high alunlinum oxide concentration at the grain boundaries was responsible. The 0.14 pct Al wire remained ductile and all further data were derived using this alloy. One-half of this wire, about 5 ft, plus 5 ft of as-homogenized wire, was then drawn cold to 0.005 in. diam. All tensile tests were conducted with an Instron Engineering Corp. tensile-testing machine, Model TT-B. Unless otherwise indicated, the tests were made at room temperature with a strain rate of 0.1 per min. All metallographic samples were etched with an aqueous solution of 2 pct each of CrO3 and H2SO4 . EXPERIMENTAL RESULTS AND DISCUSSION PARTICLE SIZE DETERMINATION A study was made of the particle size of the aluminum oxide produced in the samples of Ag + 0.14 pct Al, oxidized 1000 hr at 800°C. A cross section of the as-oxidized wire was mounted in bakelite, polished, and etched with an aqueous solution of 2 pct each of CrO3 and H2SO4. The specimen was then thoroughly cleaned by stripping successive coatings made by applying 10 pct nitrocellulose in amyl acetate. The final replica of the cross section was made by applying 2 pct nitrocellulose in amyl acetate. The replica was stripped, transferred to a copper screen, shadow cast with chromium at 10 deg and photographs taken using a Phillips Metallix electron microscope at an accelerating potential of 100 kv. A photograph of an etched sample of the as-oxidized material is shown in Fig. 2. We believe the pits in the photograph are places were A12O3 inclusions were sitting in the matrix. By inspection, it appears that the volume fraction ob-

Jan 1, 1960

By W. C. Hagel, H. J. Beattie

Seven austenitic alloys of varions base compositions and minor-alloy additions were solution-treated, aged systematically between 1200oand 1800oF, and examined by X-ray and electron metallography. Intragranular preczpitations of µ, Laves, s, ?', Ni3Ti, and x phases were observed as a function of composition and aging time and temperatwre. Phase solubility limits were detevtnitzed within 100Fo intervals. These inter metallic compounds fall into two distinct general classes, and whichever class predomznates depends on base composition. It has become increasingly evident that multicom-ponent austenitic alloys are well characterized by their precipitation processes. Since certain groups of elements act as one, the relationships among these processes are reasonably simple; complete identification of such processes is usually attainable by a systematic aging study with a combination of techniques centered on microscopy and diffraction. Several nickel- and cobalt-base alloys illustrating cellular precipitation and its interaction with general precipitation were reported previously.1 The group of alloys covered in the present paper demonstrates precipitation-hardening reactions involving two distinct classes of intermetallic compounds where the predominating class appears to depend on base composition. This dependency ties in with a crystal-chemistry regularity first observed some twenty years ago by Laves and Wallbaum but never amplified to our knowledge. Results of electron-microscope and X-ray diffraction studies on systematically aged hot-rolled alloys known commercially as S-816, S-590, Rene-41, Incoloy-901, M-308, and M-647 are reported here. Some of these alloys have previously undergone minor-phase analyses by other investiators. Alloy S-816 was investigated by Rosenbaum, Lane and Grant,3 and Weeton and Signorelli.4 Rosenbaum found only CbC in hot-rolled bars. Lane and Grant found CbC and a small amount of M6C in the cast structure and stated that both carbides form during aging, most of the precipitation being CbC. Weeton and Signorelli found CbC, M23C6 and a weak indication of a phase after a slow step-down cooling cycle from 2250°F. Rosenbaum also investigated hot-rolled samples of S-590 and identified CbC and M6C. Preliminary information on Rene-41, gained partly from the present work, was reported by Morris.5 Long-time precipitation phenomena in Incoloy-901 at 1350°Fwere investigated by Clark and Iwanski.B heir raw data re- semble those of our present heat with 0.1 pct B, while their interpretation of these data resembles our interpretation of data from another heat with only 0.001 pct B; they made no statement as to boron content. No previous minor-phase studies of alloys M-308 or M-647 have been reported. EXPERIMENTAL METHODS Table I gives alloy compositions in both weight and atomic percent. Specimens were solution-treated from 1700º to 2200ºF, aged at logarithmic-time intervals up to 1000 hours between 1200 and 1800 F, and examined in accordance with procedures previously described in detail. ' ' Phase extractions were carried out in electrolytic cells containing 800 ml of either 7 pct HC1 in denatured ethanol or 20 pct H3PO4 in water. After electrolysis for 48 hr at 0.1 to 0.2 amp per sq inch, residues were separated by filtration or centrifuging. X-ray powder patterns of residues were recorded on a diffractometer for accuracy and on film for sensitivity. Lattice parameters were calculated by least-squares analyses of indexed sin 8 values, and relative abundances were estimated from intensities of strongest lines of each phase. These phase abundances denote relative amounts with respect to each other rather than to the alloy. Mechanically polished specimens were etched in a freshly mixed solution of 92 pct HC1, 5 pct H2SO4, and 3 pct HNO3. Parlodion replicas for the electron microscope were chromium-shadowed in high vacuum at a glancing angle of 20deg. All electron micrographs are reproduced here with the shadowing source above. The correspondence betweenelectronmicrostructures and phases identified by X-rays was established by a high redundancy of correlation between relative amounts at different stages of aging and examination above and below critical transformation or solubility temperatures. EXPERIMENTAL RESULTS S-816 and S-590—The phases found in S-816 and S-590 after various aging and solutioning treatments are listed in Table 11. These data and the observed

Jan 1, 1962

By Raymond C. Boettner

The present work had for its purpose: 1) the identification of crack nucleation sites in AISI 4340, quenched to martensite and tempered over a range of 'temperatures; and 2) the comparison of fatigue processes in AISI 4340 with processes observed previously in pure metals From constant def1ection-bending fatigue tests, martensite boundaries were identified as the favored crack nucleation sites in quenched and tempered AISI 4340. It, also, was concluded that the fatigue processes operating- in this lous-alloy steel were similar to Processes observed in pure tnetals. ALTHOUGH much engineering data has been accumulated on the fatigue properties of quenched and tempered martensitic steels,' fatigue as a process is not as well understood in martensite as it is in pure metals.' Important features of the fatigue process, such as the identity of the nucleation sites, have not been determined in the commercially important high-strength low-alloy structural steels. The present work had for its purpose: 1) the identification of crack nucleation sites in a low-alloy steel, i.e., AISI 4340, which had been quenched to martensite and tempered over a range of temperatures; and 2) the comparison of fatigue processes in the AISI 4340 with processes observed previously in pure metals. This comparison of the fatigue processes in the different tempers was restricted to the high-strain low-cycle part of the S-N curve. Under these test conditions, previous work on a number of metals has shown that a large number of cracks are nucleated in less than 30 pct of the fatigue life.3 Furthermore, crack nucleation sites are not restricted to inclusions but are also associated with intrinsic structural characteristics of the metal. MATERIAL A 20-lb ingot of vacuum-melted AISI 4340 (for composition see Table I) was hot-rolled to 1-in.-diam rod and then cold-rolled to a 1-in.-wide strip, 0.08 in. thick. Fatigue specimens, see insert of Fig. 1, were machined from the strip with the long dimension parallel to the rolling direction. m this orientation, the stringers of 1 to 2 p inclusions present in the sheet lay parallel to the stress axis in the specimens. The specimens were austenitited at 2050°F in order to obtain a large prior austenite grain size, i.e., 2 mm, which facilitated the subsequent identification of the prior austenite boundaries. A helium atmosphere was used to minimize decarburization. After austenitiza-tion at 2050°F, the specimens were transferred to a 1450°F furnace so that specimen distortion was held to a minimum in the subsequent oil quench. Previous work4 indicated that refrigeration in liquid nitrogen prior to tempering reduced the percentage of retained austenite in the quenched specimens to less than 5 pct. Tempering was carried out in air over the temperature interval of 200°to 800°F to produce a range of mechanical properties, Table I. The preparation of the fatigue specimen was completed by grinding about 0.005 in. from each surface and electropolishing in a chrome trioxide-acetic acid solution for 30 min. Examination of etched cross sections of specimens prepared in this fashion showed the foregoing specimen preparation to be adequate for the removal of the decarburized layer present after the heat treatment. Transmission electron microscopy showed that the as-quenched microstructure of this alloy consisted of a mixture of martensite plates containing either a high density of dislocations or microtwins. Previous work5'6 indicated that in the course of oil quenching autotem-pering resulted in the formation of E carbide on the martensite and microtwin boundaries. Tempering for 2 hr at temperatures up to about 400°F resulted in further precipitation of the E carbide. Finally, at about 400°F, cementite began to replace the E carbide on the martensite and microtwin boundaries in addition to forming a Widmanstatten structure within the plate matrix. EXPERIMENTAL S-N curves were obtained using electropolished specimens cycled at 1800 cpm as cantilever beams in fully reversed bending at selected constant deflections. The deflections were translated into surface strains by means of a calibration curve obtained through the use of strain gages. An argon atmosphere was used to minimize environmental effects. To investigate the development of fatigue slip bands, the specimens of the different tempers were unidirec-tionally bent to a surface strain of 0.005 to 0.007, photographed to record the location and appearance of slip bands so introduced, and then cycled to failure

Jan 1, 1968

By S. G. Epstein

Using the capillary-reservoir technique, electromi-gvation rates of cadmium and indium in liquid bismuth were measured at several temperatures. The electric mobility of cadmium Jrom 305° to 535°C and indium from 310° to 595°C can be expressed as a function of temperature by the equations UIn = 1.52 x 10-3 exp sq caz per v-sec Migraion of both solutes was cathode-divected at a rate rnore than four tiMes tHAt previously found for siluer in liquid bisnmth. The electric mobilities of cadmium and indiulrz in liquid bismuth at 500° C are nearly identical with their respective mobilities in mercury at room temperature. AS part of a systematic study of the variables which are considered to control electromigration in liquid metals, the electromigration rates of cadmium and indium in liquid bismuth have been measured. Mass transport properties of silver in liquid bismuth have been reported previously,&apos; and measurements of tin and antimony in liquid bismuth are forthcoming. Comparisons will be made with literature values for these same solutes in mercury.2&apos;3 This series of solutes was selected to determine the effect of the solute valence on its electromigration. Silver, cadmium, indium, tin, and antimony have nearly equal atomic masses but have chemical valences ranging from +1 to +5. They are all fairly soluble in bismuth above 300°C and all have radioactive isotopes, which are an aid in making analyses. EXPERIMENTAL TECHNIQUE Electromigration of cadmium and indium in liquid bismuth was measured by the modified capillary-reservoir technique previously described.&apos; In this method irradiated cadmium or indium is added to bismuth to form alloys containing about 1 wt pct solute (<2 at. pct solute). Several quartz or Pyrex capillaries: 1 mm ID and 5 cm long, vertically oriented, are simultaneously filled in the reservoir of the liquid alloy. A direct current is passed through two of the capillaries, which contain tungsten electrodes sealed in the upper end. The other capillaries sample the reservoir during the experiment. After a measured time interval the capillaries are removed from the reservoir and rapidly cooled. The glass is then broken away from the solidi- fied alloy, which is then weighed, dissolved in acid, and analyzed for solute content by chemical and radiochem-ical techniques. An electric mobility (velocity per unit field) can be calculated from the amount of solute entering or leaving each capillary by the simplified expression1 in which Ui is the electric mobility of the solute, ?mi the solute weight change, Ci the solute concentration of the reservoir, I the current, p the alloy resistivity, and l the duration of the experiment. This expression is valid as long as the experiment is terminated before a concentration gradient develops across the capillary orifice. Earlier experiments showed that the concentration gradient formed initially at the electrode changes with time and eventually reaches the orifice, due to back-diffusion. This condition produces a solute exchange between capillary and reservoir by diffusion or convection, opposing the electromigration, which results in a lower measured value for the electric mobility. To determine if the concentration gradient had reached the orifice, the capillaries used in some of the experiments were sectioned at 1-cm intervals and the solute content of the alloy from each section was radiochemically determined. A typical concentration profile for an experiment with indium in bismuth is shown in Fig. 1; cadmium in bismuth showed similar behavior. As illustrated in the graph, very little back-diffusion has occurred in the capillary containing the cathode, since the concentration gradient is confined to the upper 1 cm of the capillary. In the capillary containing the anode, however, the concentration gradient is much broader, extending nearly to the orifice, even though the net change in solute concentration is nearlv the same in both capillaries. Since cadmium and indium probably lower the density of bismuth when alloyed, depletion of the solute from the alloy adjacent to the anode would increase the density of the liquid in the uppermost region of the capillary. This would give rise to convective mixing within the capillary, causing the broadened concentration gradient. Conversely, the alloy adjacent to the cathode should have a reduced density as the solute concentration is increased by migration, explaining the "normal" concentration profiles found in these capillaries. This disparity was not found for electromigration of silver in bismuth. Both metals have similar densities at the operating temperatures, and nearly symmetrical concentration profiles were found in the two capillaries of each exueriment. This density effect was also apparently encountered when an attempt was made to measure diffusion coefficients for indium in liquid bismuth by the same technique which was successfully used to measure diffusion of silver in bismuth.&apos; Capillaries 1 mm ID and 2 cm

Jan 1, 1968

By G. R. Leverant, C. P. Sullivan

To evaluate the effect of a dispersion of nondeform-able, incoherent, second-phase particles on high-strain cyclic deformation and fracture, recrystallized TD-nickel (Ni-2ThO2) and a commercially pure nickel, Ni-200, were fatigued under strain control at total strain ranges varying from 0.009 to 0.036. Relative to the Ni-200, the slip at the surface of the TD-nickel was more wavy and discontinuous due to the presence of the thoria particles. This made crevice formation (incipient cracking) within slip bands more difficult in TD-nickel than in Ni-200. Both materials cyclically hardened to a constant (saturation) flow stress which increased with increasing plastic strain amplitude. Cellular substructures were developed in both materials during cycling. The cell size in TD-nickel was controlled by the thoria particle distribution and was independent of plastic strain amplitude over the range investigated. The cell size in Ni-ZOO was larger than that in TD-nickel at similar plastic strain amplitudes and was a function of plastic strain amplitude. These results, together with the cyclic stress-strain curves for both materials, are discussed in terms of a model for fatigue strain accommodation at saturation recently proposed by Feltner and Laird. NUMEROUS fatigue investigations have considered the interrelation of slip character, dislocation substructure, and cracking in pure metals and solid-solution alloys. However, except for the studies of the low-strain fatigue of internally oxidized copper alloys1 and cast, dispersion-strengthened lead,&apos; little is known about the effects which small, incoherent, nondeform-able, second-phase particles have on cyclic deformation and cracking processes. Effects due to the particles alone are often obscured by a dislocation substructure introduced during thermomechanical processing of dispersion-strengthened metals. In the present study, recrystallized TD-nickel and a commercially pure nickel, Ni-200, were employed to evaluate the effect of a thoria dispersion on high-strai fatigue deformation and cracking at room temperature. I) MATERIAL AND EXPERIMENTAL PROCEDURE The TD-nickel was supplied by DuPont as a 5/8-in.-thick stress-relieved plate which had been subjected to a proprietary schedule of thermomechanical treatments, and the Ni-200 as 3/4-in. bar which was subsequently annealed for 2 hr at 850°C in argon resulting in an average grain diameter of 0.05 mm. The compositions of these materials are given in Table I. The microstructure of the TD-nickel consisted of elongated grains parallel to the primary working direction with an average width of 0.16 mm, Fig. l(a). Many fine annealing twins were present indicating that the starting material was in a recrystallized condition; this supposition was confirmed by the absence of of any extensive dislocation substructure, Fig. l(b). Sheetlike stringers parallel to the rolling direction were occasionally seen both within grains and at grain boundaries. Some approximately spherical particles about 2 in diam, which may correspond to exceptionally large thoria particle aggregates, were also present. The average Young&apos;s modulus of the plate material in the rolling direction was 21.8 X 106 psi which is consistent with a {100}<001>recrystalliza-tion texture3&apos;* being prominent. In transmission microscopy, the 2.3 vol pct of thoria particles generally appeared to be uniformly distributed although some clusters, 0.1 to 0.3 in diam, of larger particles were observed as previously reported for TD-nickel sheet,5 and stringering of particles was present in some areas as welt. The average diameter of the thoria particles was 450A with a calculated mean planar center-to-center spacing of 2100A, as determined by quantitative metallographic analysis.= The 0.2 pct offset yield stress was 36,000 psi which agrees with the value predicted by the modified Orowan relation7 for edge dislocations bowing between thoria particles of the size and spacing observed in the present investigation. Fig. 2 illustrates the specimen design employed for the axial high-strain fatigue testing. Adapters were screwed onto the threaded portions of each specimen so that testing could be performed in the same manner as that reported for buttonhead specimens.8 Stressing was coincident with the working direction for both materials. The gage section of each specimen was electropolished and lightly etched prior to testing. The total strain was controlled, being varied between zero and a maximum tensile strain ranging from 0.009 to 0.036. In addition to these tests, a circum-ferentially notched TD-nickel specimen was cycled over a total strain range of 0.0075. The same strain

Jan 1, 1969

By J. F. Enrietto

Internal friction measurements were used to determine the effect of manganese on the solubility and precipitation kinetics of nitrogen. Manganese, in concentrations up to 0.75 pct, has little effect on the solubility at temperatures above 250°C. On the other hand, at Concentrations as low as 0.15 pct, manganese inhibits the formation of iron nitrides, especially Fe4N, even though it may not form a precipitnte itself. The precipitation and solubility of carbides and nitrides have been extensively investigated in the pure Fe-C and Fe-N systems.1-3 In recent years, some effort has been ispent in studying the influence of substitutional alloying elements on the behavior of carbon and nitrogen in ferrite.4 -7 In particular Fast, Dijkstra, and Sladek have investigated the effect of 0.5 pct Mn on the internal friction and hardness during the quench aging of Fe-Mn-N alloys.&apos;, &apos; They found that at low temperatures (below 200°C) the presence of 0.5 pct Mn greatly retarded quench aging. For example, after 66 hr at 200°C very little precipitation had taken place in the iron alloyed with manganese, whereas precipitation was complete after a few minutes in a pure Fe-N alloy. The effect of varying the manganese content and the details of the precipitation process were not mentioned in these papers. Fast&apos; postulated that manganese causes a local lowering of the free energy of the lattice with a resulting segregation of nitrogen atoms to these low energy sites. The segregated nitrogen atoms are bound so tightly to the manganese atoms that they cannot form a precipitate. The internal friction measurements of Dijkstra and Sladek tended to confirm the concept of segregation of nitrogen around manganese atoms, and the increase in free energy on transferring a mole of nitrogen atoms from a segregated to a "normal" lattice site was computed to be - 2800 cal. Dijkstra and Sladek9 distinguished between two types of precipitates: ortho, a nitride of appreciably different manganese content than that of the matrix, and para, a nitride with a manganese content essentially that of the matrix. With each type of precipitate a solubility, again designated ortho or para, can be associated. Since the internal friction maximum in alloys which were aged several hours at 600" C dropped almost to zero, Dijkstra and Sladek9 concluded that the ortho solubility must be very low. The effect of temperature on the ortho and para solubilities has no1: been investigated. There are obviously several gaps in our knowledge concerning the influence of manganese on the behavior of nitrogen in a-iron. It was the purpose of the experiments described in this paper to determine the following: 1) The ortho and para solubilities of nitrogen as a function of temperature. 2) The details of the precipitation process at elevated temperatures. 3) The effect of varying the manganese concentration on the above phenomena. EXPERIMENTAL PROCEDURE Internal friction is conveniently employed in studying the precipitation of nitrides and/or carbides from a -iron because it is one of the few parameters, perhaps the only one, which is not affected by the presence of the precipitate itself. For this reason, internal friction techniques were heavily relied upon in the present experiment. A) Preparat of -. All specimens were prepared from electrolytic iron and electrolytic manganese. Alloys containing 0.15, 0.33, 0.65, and 0.75 wt pct Mn were vacuum melted and cast into 25 lb ingots. After being hot rolled to 3/4 in. bars, the ingots were swaged and drawn to 0.030 in. wires. The wires wen? decarburized and denitrided by annealing at 750° C for 17 hr in flowing hydrogen saturated with warer vapor. To obtain a medium grain size, - 0.1 mm, the wires were then heated to 945oC, allowed to soak for 1 hr, furnace cooled to 750°C, and water quenched. Subsequent internal friction measurements showed that this procedure reduced the nitrogen and carbon concentrations of the alloys to less than 0.001 wt pct. The wires were nitrided by sealing them in pyrex capsules containing anhydrous ammonia and annealing them for 24 hr at 580°C, the nitrogen being retained in solid solution by quenching the capsule into water. Immediately after quenching, the wires were stored in liquid nitrogen to prevent any precipitation of nitrides. By varying the pressure of ammonia in the capsule, it was possible to produce any desired nitrogen concentration. B) Internal Friction. The internal Friction measurements were made on a torsional pendulum of the Ke type,&apos;&apos; a frequency OF 1. or 2 cps being used. For

Jan 1, 1962

By George S. Ansell, Thomas E. Davidson

It has been known for a considerable period of time that the ductility of even quite brittle materials can be enhanced if they are deformed under a superposed hydrostatic pressure of sufficient magnitude. The response of ductility to pressure, however, has been shown to vary considerably between materials. Prior work has shown that the effects of pressure upon the tensile ductility of Fe-C materials depend upon the amount, shape and distribution of the brittle cementite phase. In this current investigation, the effects of pressure upon the fracture mechanisms in a series of annealed and spheroidized Fe-C materials were examined. It was observed that the principal effect of pressure is to suppress void growth and coalescence, retard cleavage fracture and to enhance the ductility of cementite platelets in pearlite. Based upon the observed effects of pressure upon the fracture mechanisms, a proposed explanation for the enhancement in ductility by pressure and for the structure sensitivity of the phenomena is presented and discussed. THE effect of superposed pressure upon the tensile ductility of a variety of metals has been well documented.&apos;-&apos;&apos; Some of the results from several investigators are summarized in Fig. 1 where tensile ductility in terms of true strain to fracture (ef) is plotted as a function of the superposed pressure. As can be seen, a pressure of sufficient magnitude can significantly enhance the ductility of metals. However, Fig. 1 also demonstrates that the response of ductility to pressure and the form of the ductility-pressure relationship varies considerably between materials. Several explanations have been offered for the observed enhancement in ductility by a superposed pressure. Although no experimental evidence was provided, Bridgman13 and Bobrowsky10 proposed that the observed effect was due to the prevention or healing of microcracks or holes. Bulychev et a1.14 observed that cracks and voids in initially prestrained copper were healed in the necked region of a tensile specimen upon further straining while under a superposed pressure. Also, pugh5 observed that large cavities were suppressed in copper fractured in tension while under pressure. A second proposal has been forwarded by Beresnev et at al.6 This proposal is based upon the hypothesis that a material fails in a brittle manner because the normal tensile stress reaches a critical value before the shear stress is of sufficient magnitude to cause plastic flow. Since a superposed hydrostatic pressure will increase the ratio of shear to normal tensile stress, a sufficiently high hydrostatic pressure should favor plastic flow while retarding brittle fracture. Galli15 reported that a superposed pressure shifts the ductile-brittle transition temperature of molybdenum. This was explained based upon the reduction of the normal tensile stress by the superposed pressure. Pugh5 explained the occurrence of the observed pressure induced brittle-to-ductile transition in zinc in the same manner. Davidson et al.12 proposed an explanation for the enhancement of ductility by pressure based upon the effects of pressure upon the stress-state-sensitive stages of various fracture propagation mechanisms. Basically, they proposed that pressure will retard cleavage and intergranular fracture by counteracting the required normal tensile stress or will suppress void growth. They observed suppression of intergranular fracture and void growth in magnesium by pressure. Davidson and .Ansell16 reported ductility as a function of pressure for a series of annealed and spheroidized Fe-C alloys. Fig. 2, from this prior work, demonstrates that the effect of pressure upon ductility is structure sensitive in terms of the amount, shape and distribution of the brittle cementite phase. As shown in Fig. 2, in the absence of cementite or when the cementite is in isolated particle form (spheroidized), the ductility-pressure relationship is linear and the slope decreases with increasing carbon content. In the annealed carbon-bearing alloys wherein the cementite is in the form of closely spaced platelets (pearlite) or in the form of a continuous network along prior aus-tenite boundaries (1.1 pct C material), ductility as a function of pressure is nonlinear (polynomial relationship) in which the slope increases with increasing pressure. At the highest pressures studied (22.8 kbars), the slope of the curves for these materials tends to approach those for the spheroidized material of the same carbon content. In this current investigation the change in fracture mechanisms as a function of pressure for the materials shown in Fig. 2 has been examined. The possible connection between the observed effects of pressure upon the fracture mechanisms and the effect of pressure upon ductility is discussed.

Jan 1, 1970

By K. T. Aust

It is proposed that the intergranular corrosion of austenitic stainless steels is associated with the presence of continuous grain houndary paths of either second phase, or solute segregate resulting from solute-vacancy interactions. Experimental observations of structural changes and crrosion behavior of different types of austenitic stainless steel provide support for this poposal. On the basis of this model, it is shown that the intergranular -corrosion susceptibility of austenitic stainless steels in nitric-dic hromate solution may be substantially reduced either by suitable heat treatments or by impurity control. AUSTENITIC stainless steels, such as Type 304, generally have excellent corrosion resistant properties when properly solution heat-treated and used at temperatures where carbide precipitation is slow. However, several corrosion environments have been found which produce intergranular corrosion of solu-tion-treated stainless steels, that is, those steels with no detectable carbide precipitation.&apos;&apos;2 Of the various corrosion environments, the most widely used test solution has been the boiling nitric-dichromate solution. In these acid solutions, stainless steels have been found to be susceptible to intergranular attack despite the addition of carbide-forming elements such as titanium or columbium, or despite lowering of the carbon content or use of high-temperature solution treatments. Studies of the electrochemical mechanism of corrosion attack have been made by several worke1s3&apos;4 who found that oxidizing ions such as crt6 depolarize the cathodic reactions and consequently raise the open-circuit potential of stainless steel immersed in nitric acids. As a result of this, the anodic reaction is accelerated. The reason for the localization of anodic activity at the grain boundaries, and resulting intergranular corrosion, has not been conclusively determined. Several workers, e.g., Streicher,3 and Coriou et al.,4 have suggested that the strain energy associated with grain boundaries provides the driving force for the accelerated intergranular corrosion. This argument would predict that alloys of high purity would still be susceptible to intergranular attack. However, work by chaudron5 and by ArmijO,6 has shown that high-purity alloys are immune to attack, in disagreement with this argument. An alternative suggestion is that chemical concentration differences exist between grains and grain boundaries, that is, impurity segregation at boundaries, and that these chemical differences provide the driving force for localized attack. It is this impurity segregation which can lead to accelerated dissolution of grain boundaries when the alloy is exposed to a suitable corrodant. This mechanism would predict the immunity of high-purity alloys to inter-granular attack, which is in agreement with experi-mental observations. In the present paper, some recent studies on inter-granular corrosion of austenitic stainless steels which were conducted by coworkers and myself will be re-tibility A simple model will be described in which it is proposed that the intergranular corrosion of aus-tenitic stainless steel is associated with the presence of continuous grain boundary paths of either second phase or solute-segregated regions.* On the basis of this model, it is suggested that the intergranular corrosion rate can be markedly reduced by the formation of a discontinuous second phase at the grain boundaries if the discontinuous second phase incorporates the major part of the segregating solute, drained from the grain boundary region. Results are presented of corrosion tests and electron microscopic studies of different types of austenitic stainless steel after various heat treatments which provide experimental support for this model. Finally, a solute clustering mechanism, based on a solute-vacancy interaction, is shown to be consistent with the results obtained for inter-granular corrosion of solution-treated austenitic stainless steels. EXPERIMENTAL Corrosion tests using weight loss measurements were made on sheet specimens, which were lightly electropolished, washed, and immersed in boiling (115°C) 5 N HN03 containing 4 g crt+6 per liter added as potassium dichromate. Studies in which the inter-granular penetration depth was measured both by electrical resistance and metallographic methods have shown an empirical correlation between the rate of intergranular penetration and the weight loss per unit time for identically treated specimens of stainless steel." As a result, although all the corrosion data reported here are in terms of simple weight loss measurements, these data are considered to reflect primarily the rate of intergranular dissolution. Fig. 1 shows a typical result of intergranular attack of a solution-treated Type 304 stainless steel after 4 hr in a boiling nitric-dichromate solution. The wide grain boundary grooving at the surface, and the attack at incoherent twin boundaries, are evident; very little corrosion attack is seen at the coherent twin boundaries. INTERGRANULAR CORROSION MODEL

Jan 1, 1970

By A. Lubinski

In drilling operations, attention generally is given to hole angles rather than to changes of angle, in spite of the fact that the latter are responsible for drilling and production troubles. The paper presents means for specifying maximum permissible changes of hole angle to insure a trouble-free hole, using a minimum amount of surveys. It is expected that the paper will result in a decrease of drilling costs, not only by avoiding troubles, but also by removing the fear of such troubles. SUMMARY, CONCLUSIONS AND RECOMMENDATIONS Excessive dog-legs result in such troubles as fatigue failures of drill pipe, fatigue failures of drill-collar connections, worn tool joints and drill pipe, key seats, grooved casing, etc. Most of these detrimental effects greatly increase with the amount of tension to which drill pipe is subjected in the dog-leg. Therefore, the closer a dog-leg is to the total anticipated depth, the greater becomes its acceptable severity. Very large collar-to-hole clearances will cause fatigue of drill-collar connections and shorten their life, even in very mild dog-legs. Another finding regarding fatiguing of collar connections in dog-legs is that rotating with the bit off bottom sometimes may be worse than drilling with the full weight of drill collars on the bit, mainly in highly inclined holes when the inclination decreases with depth in the dog-leg. Means are given for specifying maximum dog-legs compatible with trouble-free holes. An inexpensive technique proposed is to take inclinometer or directional surveys far apart; then, if an excessive dog-leg is detected in some interval, intermediate close-spaced surveys are run in this interval. The application of the findings should result in a decrease of drilling costs, not only by avoiding troubles, but mainly by removing the fear of such troubles. The result would be much more frequent drilling with heavy weights on bit, regardless of hole deviation. Because of errors inherent to their use, presently available surveys are not very suitable for detecting dog-legs. There is a need for instruments especially adapted to dog-leg surveys. Crooked hole drilling rules should fall into two distinct categories—(1) those whose purpose is to bottom the hole as desired, and (2) those whose purpose is to insure a trouble-free hole. Three kinds of first-category rules in usage today are as follows. 1. A means to bottom the hole as desired is to prevent the bottom of the hole from being horizontally too far from the surface location; this may be achieved by keeping the hole inclination below some maximum permissible value such as, for instance, 5. 2. Another means to achieve the same goal is to limit the rate at which the inclination is allowed to increase with depth. A frequently used rate is 1/1,000 ft. In other words, a maximum deviation of l° is allowed at 1,000 ft, 2 at 2,000 ft, 3 at 3,000 ft, etc. 3. Whenever application of the first two means precludes carrying the full weight on bit required for most economical drilling, then the best course is to take advantage of the natural tendency of the hole to drift updip, displace the surface location accordingly and impose a target area within which the hole should be bottomed. This method has already been successfully applied,&apos;.&apos; and its usage probably will become more frequent in the future. Means for calculating the amount of necessary surface location displacement are avail-able.3&apos;5&apos;6 If in high-dip formations the full weight on bit should result in unreasonably great deviations, the situation could be remedied by increasing the size of collars and (if needed) the size of both hole and collars,351 or in some cases by using several stabilizers. Rules which would fall into the second category (i.e., rules whose purpose is to insure a trouble-free hole) are seldom specified today. It is vaguely believed that following Rules 1 and 2 of the first category will automatically prevent troubles. Actually, this is not true. If at some depth the only specified rule is that the hole inclination must be less than 4", the hole may be lost if the deviation suddenly drops from 4 to 2, or if the direction of the drift changes, etc. Rule 3 of the first category is generally used in conjunction with a rule belonging to the second category, namely, that the hole curvature&apos; (dog-leg severity) must not exceed the arbitrarily chosen value of 1½ /100 ft. Moreover, when using this rule, the industry is not clear over what depth intervals the hole curvature should be measured. All this results in a frequent fear

By H. C. Theuerer

GeC14 may be purified by extraction with HCI and chlorine. The process is as effective for the removal of AsCI:, as the more cumbersome distillation methods usually used for this purpose. GERMANIUM for semiconductor use contains impurities at levels no higher than a few parts in ten million. Material of this quality is obtained from highly purified GeC1, by hydrolysis to the oxide and reduction of the oxide in hydrogen. When purifying GeCl,, AsC1, is the most difficult impurity to remove. This is usually accomplished by multiple distillation procedures.1-3 AsC1, may also be removed from GeC1, by extraction with HC1.1-4 Reducing the arsenic to low concentrations is not practicable, however, because of the large number of extractions needed. This paper discusses a new method for the removal of arsenic from GeC1, by extraction with HC1 and chlorine. The method is rapid, leads to little loss of germanium and is at least as efficient as the distillation procedures currently being used. Theory of Extraction Procedures In the simple extraction of GeC1, with HC1, the following reaction occurs ASCl8G8C1 D AsCl3rc1 at equilibrium CA/Cn= K, where K is the distribution coefficient, and C, and C,, are the molar concentrations of AsC13 in HC1 and GeCl,, respectively. The materials balance equation for this reaction is VACA + vncn = VnC,, where V, and Vn are the volumes of HC1 and GeCl4, respectively, and C, is the initial concentration of AsC13 in GeC1,. From this it can be shown that for multiple extractions where C,, is the concentration of AsC13 in GeC14 after n extractions, and r is the ratio of V, to V,,. It is assumed that r is maintained constant, that equilibrium is established during each extraction, and that K is independent of the AsCl3 concentration. By saturating the system with chlorine, the following reaction occurs in the aqueous phase AsCl3 + 4H2O + Cl2 D H5AsO4 + 5HC1 at equilibrium K&apos; = ------------ ai - a4 h2u - aet2 where a is the activity of the various components. The effect of this reaction is to reduce the concentration of the AsC1, in the aqueous layer and, therefore, to promote further extraction of this component from the GeC1, layer. If the arsenic acid remains entirely in the aqueous phase, the net effect of this reaction is to promote the removal of arsenic from the GeC11. The materials balance equation for extraction with HC1 and chlorine with the foregoing reaction is, then, VaCC + VACA + VACn = VnCo where C,. is the molar concentration of H3AsO, in the HC1. With the added assumptions that the activities of AsC13 and H8ASO4 in the aqueous phase are equal to their molar concentrations, it can be shown that for n extractions Cn/Cu = (1/rkK + rK + 1) n where k - K1 a4h2o - acl2/aoncl. It can be seen by comparing Eqs. 1 and 2 that if k is large, the removal of AsC1, by HC1 extraction will be greatly improved by the addition of chlorine. Dilution of the HCI used in the extraction with chlorine would also favor the separation. This, however, would increase the loss of GeCl,, which is undesirable. Experimental Procedure Germanium prepared from oxide of semiconductor purity is n-type with resistivities greater than one ohm-cm. The resistivity is controlled by the donor concentration, which is —lo-: mol pct. Germanium prepared from material with added arsenic will have lower resistivity commensurate with the arsenic concentration. With such material, at arsenic concentrations above 10-1 mol pct the resistivity is controlled by the added arsenic, and effects due to other impurities initially in the oxide are negligible. In this investigation GeO, of semiconductor purity was converted to GeCl,, and -0.01 mol pct As was added. This material was used for the extraction experiments and the purification attained determined by a comparison of the resistivity data for samples of germanium prepared from the initial and purified GeC1,. A method for calculating the arsenic concentration from the resistivity data is discussed later. The details of the experimental procedures used are as follows: Two hundred and thirty cu cm GeC1, were prepared by the solution of GeO, in HC1, followed by

Jan 1, 1957

By H. S. Chiang, D. F. Lu, S. S. Peng

INTRODUCTION The most important element in a successful lingual mining is a good roof control. The modern longwall mining employs hydraulic powered supports for roof control at the face area. The application of hydrau¬lic powered support requires the knowledge of over¬burden strata behavior for proper selection of sup¬port type and capacity. Failure to do so could lead so serious loss. There are several methods available for determining the required support capacity (1-3). While these methods are simple for application, they do not include the complicated roof behavior observed in longwall mining. As research progresses and operational experience accumulates (4,5), the concept about the designing and selection of powered support improves. The design of a longwall powered support consists of three major phases: 1. structural integrity and stability of the powered support, 2. external loadings induced by the movements of the overburden strata, and 3. interaction between the support, roof and floor. Phase 1 involves structural analysis (5) and full-sized testing (6) of the supports. Its validity is limited by the accuracy of the assumed external loading because of the uncertainty about the actual loading underground. The third phase includes the reaction of the support and the floor to the movements of the overburden strata and vice versa. Among the three phases, the second phase concer¬ning the external loading seems to be the least known because of the complicated behavior of the roof strata. There are many unresolved problems. For example, does the main roof break periodically and cause periodic roof weighting in the face area? If so, are there any rules governing its behavior? How does the roof load on the support canopy! Finally, how can one determine the required support capacity and select a proper type of support to meet a certain roof behavior? In order to answer those questions, underground instrumentation and observations were performed at 4 longwall panels in 3 separate mines for the past two years. This paper summarizes the current findings. PANEL LAYOUTS AND EQUIPMENT EMPLOYED The three mines selected are all located in West Virginia; two in northern and one in southern West Virginia. As shown in Table 1, seam conditions (i.e. seam, depth and thickness) and panel layouts are different among the three mines. The most significant difference in equipment is the face powered supports. Three mines used three different types of shield; 2-leg caliper, 2-leg lemniscate, and 4-leg lemniscate chock-shield. (Fig. 1) UNDERGROUND INSTRUMENTATION AND OBSERVATION PROGRAM Two events were instrumented in each observed longwall face: one was the hydraulic pressure (resistance) of the powered supports and the other was the canopy load distributions. In addition, the gob caving conditions were visually observed and recorded. Leg and Support Resistances One or two automatic Weksler Pressure Recorders were installed at the designated shield support,. In most cases, the daily charts were used to record the pressure variations in both the front or the rear legs (for the 4-leg shield), or in both the leg and the fore-pole ram (for the 2-leg shield). The recorded pressure w a s then converted to load or resistance by multiplying it by the cross-sectional area of the hydraulic leg or canopy ram piston. Fig. 2 shows the typical pressure-recorded charts for the 4-leg and 2-leg shields in a 23-24 hour period. The support resistance is the summation of the resistance in each of all the legs for that support. Generally, the resistance of the fore-pole ram will not be considered in determining the capacity of the support because of its rather small vertical compo¬nent force at the tip of the fore-pole. Canopy Load Distribution External load distribution on the canopy as exer¬ted by the roof was monitored. The measurements employed 12-14 pieces of pressure cells (6-inch square) that were uniformly arranged in two rows on the canopy. After support setting, the pressure changes in the cells were monitored at various stages of the mining (supporting) cycle while the support leg pressures were recorded continuously by the pressure recorders. Based on the calibration chara¬cteristics of each pressure cell as performed in the laboratory before and after each underground test, the cell pressures were converted to actual loadings. From these load measurements the canopy load distri¬butions and the relations between measured canopy loadings and support leg resistances were determined. Accordingly, the supporting efficiency of the shield support can be determined.

Jan 1, 1982

By P. N. Richards, M. K. Ormay

The present Paper extends the previous work on cold reduced, low carbon steels to preferred orientations developed after various heat treatments. In recrystal-lized rimmed steel, cube-on-comer orientations increased with cold reductions up to 80 pct. Above that {111}<112> and a partial fiber texture with (1,6,11) in the rolling direction dominated. During grain growth, cube-on-corner orientations have been observed to grow at the expense of {210}<00l>. In re-crystallized Si-Fe (111) (112) and cube-on-edge type orientations are dominant near the surface and the (1,6,11) texture near the midplane for reductions up to 60 pct. With larger reductions {111)}<112> and the (1,6,11) texture are dominant. In cross rolled capped steel a relationship of 30 deg rotation was observed between the (100)[011] of the rolling texture and the main orientations after re crystallization. Most orientations present in recrystallized specimens can be related to components of the rolling texture by one of the following rotations: a) 25 to 35 deg about a (110) b) 55 deg about a (110) C) 30 deg about a (Ill) THE orientation texture of recrystallized steel is of interest where the product is to be deep drawn, because preferred orientation is related to anisotropy of mechanical properties such as the plastic strain ratio (r value);1,2 and in electrical steel applications where a high concentration of [loo] directions in the plane of the sheet improves the magnetic properties of the material. It is interesting to note that both these aims are to a large extent achieved commercially, even though the orientation texture of cold rolled steel does not show large variation3 and the recrystallized orientations are generally given as being related to the as rolled orientations mostly by 25 to 35 deg rotations about common (110) directions.4-6 There is, as yet, no single completely accepted theory on recrystallization. The three mechanisms that have been investigated and discussed are: a) Oriented growth b) Oriented nucleation c) Oriented nucleation, selective growth Largely from the observations of the recrystalliza-tion process by means of the electron microscope,7-11 there is now considerable evidence that the "nucleus" of the recrystallized grain is produced by the coalescence of a few subgrains to form a larger composite subgrain, which finally grows by high angle boundary migration into the deformed matrix. From the intensive work on the recrystallization of rolled single crystals of iron, Fe-A1 and Fe-Si al-loys4-" he following observations have been made: 1) The change in orientation during primary recrys-tallization can usually be described as a rotation of 25 to 36 deg about one of the (110) directions. 2) The (110) axes of rotation often coincide with poles of active (110) slip planes. 3) If several orientations are present in the cold rolled structure, the (110) axis of rotation will preferably be a (110) direction that is common to two or more of the orientations. 4) With larger amounts of cold reduction (70 pct or more) departure from these observations became more frequent. 5) After larger cold reductions, rotations on re-crystallization about (111) and (100) directions have been observed. K. Detert12 infers that a rotation relationship of 55 deg about (110) directions is also possible, by stating that the recrystallized orientation {111}<112> can form from the orientation {100}<011> of cold reduced partial fiber texture A.3 The observation by Michalak and schoone13 that (lll)[l10] formed during recrys-tallization in fully killed steel containing (111)[112],— as well as (001)[ 110] which is related to the {111}<011> by a 55 deg rotation about <110>-implies a possible 30 deg rotation relationship about the common [Ill]. Heyer, McCabe, and Elias14 have recrystallized rimmed steel after various amounts of cold reduction, by a rapid and by a slow heating cycle and found that the preferred orientations strengthened with increased cold reduction. The most pronounced orientation up to about 70 pct cold reduction was found to be {1 11}< 110>, after 80 pct cold reduction both {111}<110> and {111}<112>, after 85 and 90 pct cold reduction, {111}<112>, and after 97.5 pct cold reduction it was {111}<112> and (100)(012). In the present work, the orientation textures of the recrystallized specimens are examined under various conditions of steel composition, amount and method of cold reduction, and method of recrystallization. The relationships between the preferred orientations of the as rolled and recrystallized specimens, and the conditions for the formation of the various orientations during recrystallization are investigated.

Jan 1, 1970

By R. M. Waterstrat

The phases occurring in the V-Mn system were studied by means of X-yay diffraction and metallo-paphic techniques, using are-melted alloy specimens annealed in the temperature range 800° to 1150°C and quenched. The bcc solid solution extends at 1250°C all the way from vanadium to 6-manganese. Below 1050°C the a-phase is formed, and the terminal a-manganese phase is stabilized up to about 900°C by vanadium in solid solution. IN the only previous general survey of the V-Mn system Cornelius, Bungardt and Schiedtl reported the existence of three intermediate phases corresponding to the approximate compositions VMn,, VMn, and V5Mn. The phase VMn8 has recently been identified as a o phase2 but the alloy VMn was found to have a bcc structure2 corresponding apparently to the vanadium solid solution rather than to the large cubic unit cell reported by Cornelius et al. 1 Subsequent work by Rostoker and Yamamoto3 has shown that the vanadium-base bcc solid solution extends to at least 15 pct Mn at 900°C. An alloy corresponding to the composition VMn, was examined by Elliott,4 who reported that the as-cast sample as well as samples annealed at 1200o and 1300°C had bcc structures, but that annealing at 1000°, 800") and 600°C produced two phases. One of these phases was apparently the bcc solid solution and the other resembled the o phase structure. Hellawell and Hume-Rothery5 established the phase relationships in manganese-rich alloys above 1000°C, and showed that the o phase in this system is replaced by the 6 Mn (bcc) solid solution at temperatures above 1050°C. These results suggest that a continuous bcc solid solution may exist above 1050°C between vanadium and 6 Mn. The present investigation was undertaken in order to develop more complete information in regard to this system. EXPERIMENTAL METHODS The alloys used in the present work were prepared by arc-melting electrolytic manganese having a minimum purity of 99.9 pct and vanadium lumps with a purity of 99.7 pct. The major impurities present in these metals were carbon, nitrogen, and oxygen and this would account for the small percentage of nonmetallic inclusions observed metal-lographically. The arc-melting was at first performed under a helium atmosphere and it was necessary to keep the melting times as short as possible in order to minimize the loss of manganese by vaporization. It was later found that the evaporation of manganese was considerably reduced when the melting was done under argon atmosphere. The final composition of each alloy was calculated by assuming that the total weight loss during melting was due to evaporation of manganese. Compositions which were calculated in this manner agreed reasonably well with the results of chemical analysis, as shown in Table I. Spectrographic analysis revealed the presence of contamination by tungsten, but in no case was the percentage of tungsten greater then 0.4 at. pct. The specimens were in each case broken in half and the fractured section was examined visually and microscopically for evidence of inhomogeneity. Each specimen was homogenized at temperatures near l100°C, as shown in Table I. After this treatment most specimens consisted of large columnar grains of the bcc vanadium solid solution. The etchant used in most of the metallographic work consisted of 20 pct nitric acid, 20 pct hydro-flouric acid, and 60 pct glycerine. It was found that this etchant would clearly delineate the phases present in these alloys although it does not produce any striking contrast between the phases. For certain manganese-rich alloys, a 1 pct aqueous solution of nitric acid was used. This etchant gave a brown color to the a-manganese phase, whereas the o phase was virtually unattacked and appeared very light as shown in Fig. 1. The etchants used by Cornelius et a1.l were found to produce spurious effects in some of these alloys. In particular, the vanadium-rich alloys etched in hot sulfuric acid often appeared to consist of two phases when both X-ray diffraction and etching with the glycerine-acid mixture indicated the presence of single phase bcc solid solution. A few percent of what appears to be an oxide or nitride phase was found at the grain boundaries and in the interior of the grains, especially in the vanadium-rich alloys. All alloys were annealed in sealed silica tubes containing 1 atm of pure argon and these tubes were then quenched in cold water. Although some manganese loss occurred during annealing, the loss seemed to be confined to the surface of the speci-

Jan 1, 1962

By K. E. J. Rapperport, C. S. Hartley

The only slip system observed in zirconium crystals deformed at 77", 575", and 1075OK was (1010) [1210] with a critical resolved shear stress in tension of 1.0 kg per sq mm at 77°K; 0.2 kg per sq mm at 575 °K; and 0.02 kg per sq mm at 1075 OK. The active twin planes were {1012}, (1121}, (11221, and (11233) with varying temperature dependence. A detailed analysis for the slip direction using Laue spot asterism is appended. NeARLY all metals of the hexagonal close-packed structure exhibit basal slip, i. e.,(0002)<1120>- type slip. This is true of magnesium,&apos; zinc,&apos; cadmium,3 beryllium,4 titanium,= yttrium,6 and rhenium.Many of these such as titanium 5&apos;8-&apos;0beryllium,4&apos;" magnesium, and zinc13&apos;14 display other slip modes even at room temperature, and nearly all have been reported to slip on other systems under particular loading or temperature conditions of testing. As is shown in this paper, basal slip was not found at any of four test temperatures from 77" to 1075°K in hexagonal close-packed zirconium under the simple loading conditions of tension and compression, even though in one case the resolved shear stress on the inactive (0002) <llgO> system was twenty-five times higher than the critical resolved shear stress on the active (1010) [1210] system. This result is consistent with prior studies on the active deformation processes in zirconium deformed at room temperature. &apos;&apos;-I7 SPECIMEN PREPARATION A) Material—The zirconium used in this work was of two types: 1) as-deposited reactor grade crystal-bar, and 2) arc-melted and forged reactor grade crystal-bar. Typical chemical and spectrographic analyses of these materials as received, and after hydrogen removal and crystal growth are given in Ref. 17. Crystals of type 1) above have the letter prefix (A) and those of type 2) have the prefix (B) throughout this paper. B) Crystal Growth— he zirconium was machined into rectangular parallelepipeds about 0.2-in. scl in cross section and 2 in. iong. These were hand polished through 4/0 abrasive paper, electropolished, given a hydrogen removal anneal, and subjected to long-time anneals at 840 °C in vacuo to produce usable crystals.&apos;7 A second technique used to obtain large crystals was to cycle the samples two or three times between 1200" and 840°C, allowing them to remain at the higher temperature for about 4 hr and at the lower temperature for 5 days.17 These techniques yielded some grains which occupied the entire cross section of the bar and were as long as 3/4 in. C) Orientation Determination—After the growth of large crystals by thermal cycling, the samples were repolished with extreme care through 4/0 abrasive paper and electropolished. Metallographic examination after polishing showed the surfaces to be free of visible deformation traces. Standard Laue back-reflection X-ray techniques were used to find the crystallographic orientations of selected large grains with respect to a specimen face and edge. Fig. 1 shows the stereographic projections of the stress axes for the crystals used. The sharpness of the spots on the Laue photographs indicated that the crystals were of good quality. EXPERIMENTAL METHODS Nine crystals were deformed in tension at 77"K, nine in tension and five in compression at 300°K in previous tests,17 fifteen in tension at 575"K, and eleven in tension at 1075°K. All specimens were stressed by load increments. After a predetermined load was applied, the specimen was removed from the loading appratus and metallographically examined for deformation traces. An attempt was made to initially stress each bar so that some crystals slipped a small amount and others not at all. This was done to bracket the critical resolved shear stress. One bar of special orientation (B-11) was repolished and annealed at 1075°K for 1 hr after lower temperature deformation, before final deformation at 1075°K. In the other bars the loading by increments, followed by metallographic examination, was continued until the surface distortion would interfere with analysis, or until fracture. One example of a crystal pulled to fracture is shown in Fig. 2. This photograph shows a crystal (B-14C) which was pulled at 1075°K and failed by slip on two (10i0) planes. The approximate orientation of this crystal is illustrated in the figure. Specimens were deformed at 77°K in liquid nitrogen on a tensile machine using an insulated bucket with an internal hook to accept a clamped specimen.

Jan 1, 1961